Jump to content
SAU Community

Recommended Posts

Hi

I noticed that this sensor or something at the front of the dash on the left hand side was wondering if anyone could tell me what it is or for ???

I thought it was a Head light auto sensor but I don't have any switch or toggle that operates it :)

If it helps its a Autech 260RS 1999 s2

post-47234-1271596839_thumb.jpg

post-47234-1271596860_thumb.jpg

Edited by e-clip
Link to comment
https://www.sau.com.au/forums/topic/317239-dash-sensor/
Share on other sites

is it also used for the outside temp function?

(i.e. when you press the temp knob?)

nah the outside air temp one is mounted in the front bar just under the a/c thermo fan. if you have a front mount it may have been moved. the purpose of the sunload sensor (the one of the left side of the dash) is as others have said, it tell the auto a/c control that you are in the sun and the a/c will work a little harder to try and compensate for the suns heat. the sunload sensor doesn't switch the autolights.

Link to comment
https://www.sau.com.au/forums/topic/317239-dash-sensor/#findComment-5190362
Share on other sites

You can find out the outside temp? This is news to me. I'll have to try it.

What does the auto switch for the head lights look like?

Same here ... How do you find out the outside air temp on a series 1 ?

On a series 1, you can't find out the outside temperature, but on a series 2, you push in on the dial that you use to adjust the air-con temperature.

Link to comment
https://www.sau.com.au/forums/topic/317239-dash-sensor/#findComment-5191167
Share on other sites

You can find out the outside temp? This is news to me. I'll have to try it.

What does the auto switch for the head lights look like?

Well on the S1 the auto headlights function is on the same switch as the main beams:

1.OFF

2.auto

3.side

4main

nb apparently this is an option on some models so some people may not have it.

Link to comment
https://www.sau.com.au/forums/topic/317239-dash-sensor/#findComment-5191210
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani Refurbed astra pump thats the cover for it in the boot I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
    • I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
    • lol no cats running str pipes … might put the high flow back on but I suspect it might effect my ignition timing a bit. 
    • That looks a bit like yellowing to me. If the rear bar was looking like that from rich idle, I'd ask the question, do you have a catalytic converter fitted, and fully working?
    • Oh yeah gets really bad down here. I’ll have to upgrade the heater and wind screen wipers as well for optimal performance.
×
×
  • Create New...