Jump to content
SAU Community

And The Award For Worst M35 Bodykit Goes To....

rb26stagea
 Share

Recommended Posts

stagman Community Regular

stagman

Posted
Posted

haha dang, I thought i must of clicked on the wrong link, cause i liked it haha. IMO it just needs to have bigger wheels, be a different colour and lower and it would look good.

iamhe77 Grand Master

iamhe77

Posted
Posted (edited)
dolphin i reckon

Correct :(

I agree, I thought the whole idea of a body kit was to work WITH and ENHANCE the factory body styling and aerodynamics... something Dolphin clearly couldn't get their design team's head around for the NM35.

Mind you, the C34 Doplhin bodykits look just as bad (just more square)

Edited by iamhe77
Jetwreck Grand Master

Jetwreck

Posted
Posted (edited)

FFS....that's one ugly kit as is.....mind you I think what Stagman has said make sense....just needs some wheels and a decent ride height and it will look better. But never awesome.....I think I'm going to have nightmares tonight though!!!!

post-37023-1273011307_thumb.jpg

Edited by Jetwreck
pixel8r Mentor

pixel8r

Posted
Posted

oh i see the usual haters have turned up again...each to their own I say.

The front is too square, but the rest isn't too bad IMO. If you stuck the factory bodykit on the front (the one with the lip at the bottom) it may look ok.

atomaly Rising Star

atomaly

Posted
Posted

C34 Dolphin kits imho are the best looking kits about.

this M35 kit is however not very asthetically pleasing to me!

but then again. the M35 in general isnt either to me :thumbsup:

although the dolphin pics are somewhat better (other ones are shit angles) i found this on the dolphin site!

ph_m35-stagea_f.jpg

ph_m35-stagea_r.jpg

iamhe77 Grand Master

iamhe77

Posted
Posted
C34 Dolphin kits imho are the best looking kits about.

this M35 kit is however not very asthetically pleasing to me!

lol.... if you saw it front on, you would change your mind

(does let a ton of air through though)

GTRWAGON Enthusiast

GTRWAGON

Posted
Posted
C34 Dolphin kits imho are the best looking kits about.

this M35 kit is however not very asthetically pleasing to me!

but then again. the M35 in general isnt either to me :P

although the dolphin pics are somewhat better (other ones are shit angles) i found this on the dolphin site!

ph_m35-stagea_f.jpg

ph_m35-stagea_r.jpg

Nice rims :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Kelford 246-A2. 262in/272ex. 
    • Adam_ECR33
      Hello sau 👋

      By Adam_ECR33 · Posted

      Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • r32-25t
      Why am I hitting a power wall with my stroked RB25?

      By r32-25t · Posted

      When you say your cams are 272/262 is that 272in and 262ex?
    • Kinkstaah
      Nismo GT Pro LSD configurations

      By Kinkstaah · Posted

      We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...