Jump to content
SAU Community

Recommended Posts

before i do the change.. 5L bottle is enough yeah??

and 10 40 is the right grade???

4.6L is recommended, but no issue putting all 5L in.

You'll be fine with 10w40 (ignore Nissan's suggested 7.5w30 = too thin)

Edited by iamhe77
  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

As long as you are aware the Nulon is not a full synthetic, they are actually false advertising. Like I said earlier, there is a thread on Oils here:

http://www.skylinesaustralia.com/forums/Go...80#entry5234530

Edited by mosoto
  • 4 months later...

Hi guys,

Just a quick question - have used Mobil 1 and Valvoline, both Full Synthetic rated at 5w-30. It's time for an oil change and I was wondering if any of you have tried Penrite SIN Plus 5w-60. Haven't seen many brands with 5w-60 around - any thoughts?

Cheers,

Tarun

how about motul 5-40w 8100 X-CESS ?

also i seen on usa sites they dont recommend synthetic oils ?

Agreed Quite a few Mechanics have told me the same not to use synthetic in the v35 3.5 v6

Also was told In the log books it says "Nissan recommends mineral based oils"

A good quality mineral oil is the way to go.

Either way if you buy a decent full syn or mineral and service it at 5000km or under, you shouldn't have any problems.

This one has a car doing a burnout on the front, it must be good. :huh:

Stick to grade 4 or 5 due to the high temps these VQ's run at all the time. 10w40 I have found to be a good compromise.

post-63525-1286076155_thumb.jpg

Fuchs 10W-40 Super GTO, Full synth.

Used it in my track car for 4 years and it held the motor together with no damage after losing ALL oil pressure when the oil cooler popped. So it's only natural that I use it in the Stag too.

Fuchs aren't too well known in the retail market, but from a lubricant engineering perspective theyre top notch. Used fuchs products in machinery for years.

Gulf Western Sougi S6000. It's a classV fully Synthetic oil @ $80 for 5litres. There's a thread on oils worth reading

+1

I have been running it for a couple of changes now (I change every 10,000kms, but I use Group V oil) and have to say that my car likes it much better than the Redline...

... so does my wallet for that matter.

If you are in Vic, you can get it from the supplier for around $60... I picked up my last 5L bottle for $80 at Autobarn!

This one has a car doing a burnout on the front, it must be good. :rant:

Stick to grade 4 or 5 due to the high temps these VQ's run at all the time. 10w40 I have found to be a good compromise.

To quote a tried & true saying: "Never judge a book by it's cover". Too many of you are wasting your money on brand name oils like Motul & Royal purple. These are great oils, I'm not argueing that fact BUT the Sougi S6000 really is as good if not possibly better. It is actually a true group V full synthetic and a true gem of a find (thanks Birds :P ). Guys save yourself $40-$50 and try the Sougi with a decent filter like a K&N HP-1008 for the V35 and you'll find no difference other than money in the bank.

:) I think you'll find that line in Scott's post was full of sarcasm.

I don't really agree that people will be wasting their money if they use Motul 300v or Redline, they are Group V oils and are absolutely brilliant.

Having said that, I find that the Sougi S 6000 is at least as good as the Motul 300v and both felt better in my car than the Redline (all 10w40).

If you can find it, buy the Sougi... it's a Group V oil at a Group IV price and VQ's love it :)

If people can't find it, then why shouldn't they still want the best oil for their pride and joy?

As an aside.... Sougi S 600 + Veruspeed oil filter = WIN :P:rant::yes:

:P I think you'll find that line in Scott's post was full of sarcasm.

I don't really agree that people will be wasting their money if they use Motul 300v or Redline

You read that out of context. They will be wasting money if they can buy the same oil for $40-$60 less.

Would you buy 5L of 300v for $140 at Autopro if supercheap had it for $80, I think probably not :rant:

Sougi >= 300v

Edited by mosoto
You read that out of context. They will be wasting money if they can buy the same oil for $40-$60 less.

Would you buy 5L of 300v for $140 at Autopro if supercheap had it for $80, I think probably not :ermm:

Sougi >= 300v

That's fine and I agree IF they can get hold of the Sougi. If they can't, then I think that spending more on a Grade V oil such as 300v/Redline rather than settling on a Grade III/IV oil can only be beneficial for the engine.

It is a damn shame that the Sougi is so hard to find...

So far on the thread there are comments on oil use in turbo and NA motors, all VQ; but with different issues regarding ideal oil.

M35 stageas have ball bearing turbos - change more often, more sensitive to dirty oil - 5w30 factory recomended, probably to help fuel economy figures and generally agreed to give high oil consumption. Most use oil with 10w40 or 15w40.

Regarding mineral, semi-synthetic, synthetic - going to full synthetic from semi or mineral is suposed to be a no no as can clean off deposits and lead to increased oil use in older engines.

ATM Using Penrite HPR 10w50 in 2002 NM35 ARX, using just under 10L/100km on highway (real km not speedo,corrected with GPS as speedo out 7%) just over 14L/100km short trips and city. Seems to be performing well on this and has used none after 2,000km. Unless I use this for the next 20,000km can't really comment on engine protection and that is what we are after isn't it?

Best oil for the VQ NA motors - well who cares - they are NA. No really they are great motors, getting my wife a GT 350. :ermm:

That's fine and I agree IF they can get hold of the Sougi. It is a damn shame that the Sougi is so hard to find...

My local Autopro can get it in whenever I ask him to as they are an outlet for GW.

That's fine and I agree IF they can get hold of the Sougi. If they can't, then I think that spending more on a Grade V oil such as 300v/Redline rather than settling on a Grade III/IV oil can only be beneficial for the engine.

It is a damn shame that the Sougi is so hard to find...

I purchased Sougi S6000 10w-40 today. I was advised that Sougi S6000 will be phased out BUT that in coming months it will be replaced with something similar. So those who think Sougi is being stopped, not so!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah and hence my ghetto way of slamming the brakes, get the ABS to cycle, rebleed seems to be a sensible workaround.
    • Hey! Happy to help. Nothing inherently wrong with the adapter, it's more so with Brett Collins himself. He gave me a lot of incorrect information when I was in contact with him and was extremely rude when I challenged him. He stated I could not use any aftermarket twin plate clutches except for his own, not to use the dush shield, bla bla bla and it was all BS.  Collins stated to cut roughly 14mm's off the housing, I took off 15mm to make room for the dust shield. I would confirm with whatever adapter manufacturer you're using. 
    • There's plenty of OEM steering arms that are bolted on. Not in the same fashion/orientation as that one, to be sure, but still. Examples of what I'm thinking of would use holes like the ones that have the downward facing studs on the GTR uprights (down the bottom end, under the driveshaft opening, near the lower balljoint) and bolt a steering arm on using only 2 bolts that would be somewhat similarly in shear as these you're complainig about. I reckon old Holdens did that, and I've never seen a broken one of those.
    • Let's be honest, most of the people designing parts like the above, aren't engineers. Sometimes they come from disciplines that gives them more qualitative feel for design than quantitive, however, plenty of them have just picked up a license to Fusion and started making things. And that's the honest part about the majority of these guys making parts like that, they don't have huge R&D teams and heaps of time or experience working out the numbers on it. Shit, most smaller teams that do have real engineers still roll with "yeah, it should be okay, and does the job, let's make them and just see"...   The smaller guys like KiwiCNC, aren't the likes of Bosch etc with proper engineering procedures, and oversights, and sign off. As such, it's why they can produce a product to market a lot quicker, but it always comes back to, question it all.   I'm still not a fan of that bolt on piece. Why not just machine it all in one go? With the right design it's possible. The only reason I can see is if they want different heights/length for the tie rod to bolt to. And if they have the cncs themselves,they can easily offer that exact feature, and just machine it all in one go. 
    • The roof is wrapped
×
×
  • Create New...