Jump to content
SAU Community

Recommended Posts

Haha!

Well got my new rear discs in finally.

322mm 350Z rear brembo. DBA 4000 slotteds. The originals were 298mm, replaced with vsII, N1 rear calipers and 322mm rotors.

They fit fine, only .5mm offset difference from original vsII, N1 rear discs, all other dimensions the same.

post-12712-0-72673800-1354422581_thumb.jpgpost-12712-0-54170300-1354422592_thumb.jpg

Also made up some carbon rear diffuser fin extensions as the stockers were a little dog eared (and small).

All up cost under $170 for structural carbon fibre sheet, rivets, rivet gun etc.

post-12712-0-04977800-1354422607_thumb.jpgpost-12712-0-06559200-1354422608_thumb.jpg

Ran down WSID, and got a best of 11.678 @ 122.56MPH 60' 1.846.

Next best: 11.744 @ 124.26MPH 60'1.843.

Out of the 4 runs I bogged it twice, and the 2 good runs I got excessive wheelspin!

More practice at launching needed :D

Car weighed in at 1622KG 1/3 tank of fuel.

After the last run though something happened as idle now sits at 600RPM. Still drive smooth, just the idle is way too low.

Must of either got a leak under the plenum for idle air control, or AAC is kaput!

Update: Well looks like the idle screw managed to wind itself in and maybe a faulty AAC valve, I wound the idle screw out and go a steady idle and put some sealant on the screw so it doesn't move around.

Yeah, needs a final tune still :) Would be nice haha!!

Looking at the vids the engine/gbox shook a fair bit on takeoff so I'm thinking something came loose to cause the idle issue.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...