Jump to content
SAU Community

How To Remove This?

SiNNO

By SiNNO,
in General Maintenance

 Share

Recommended Posts

SiNNO Experienced

SiNNO

Posted
Posted

Hey guys,

I'm in the middle of changing my spark plugs on my rb25de.

Anyone got any ideas I can try to take this rubber tube off? I already removed the clamps and used brute force but the thing won't budge.

It's the last thing I need to remove to be able to get to the coil pack cover :blink:

14062010495.jpg

Link to comment
https://www.sau.com.au/forums/topic/325007-how-to-remove-this/
Share on other sites
Duncan Grand Master

Duncan

Posted
Posted

these....are one of the essential tools for a skyline owner!

vh479.jpg

if not....you need to break the seal between the hose and the metal.

carefully work the smallest bladed screwdriver you have between the hose and the pipe (don't stab the rubber, go under it). if you can work the screwdriver right around the pipe the hose will come straight off.

Victory Mentor

Victory

Posted
Posted

Another good trick is once you have the tip of the screw driver under the rubber and can prise it up spray some WD40 into the opening. This will help to soften the hose and allow you to get the screw driver in further to brake the seal between the hose and the pipe.

I would not put hot water anywhere near this area as it would run down over the coilpacks and the spark plugs.

tiberis Enthusiast

tiberis

Posted
Posted

give it a twist.

seriously, it's the same theory as the other techniques, you just need to break the bond between rubber and metal, sometimes rotating the hose helps break the contact first, then you just pull.

might be a bit hard if the hose is really stiff, but it's helped me many times over the years.

plus it also helps for putting hoses on.

Craved Grand Master

Craved

Posted
Posted
these....are one of the essential tools for a skyline owner!

vh479.jpg

if not....you need to break the seal between the hose and the metal.

carefully work the smallest bladed screwdriver you have between the hose and the pipe (don't stab the rubber, go under it). if you can work the screwdriver right around the pipe the hose will come straight off.

i have these - these are awesome

Munkyb0y Grand Master

Munkyb0y

Posted
Posted (edited)
+1 for giving it a twist, or getting some of those hose pliers. or get the biggest flat screwdriver you have and wedge it between the steel piece and the hose and try and lever it off (basically how the hose pliers would work)

this is the way i always deal with stuck hoses.

Edited by Munkyb0y
89CAL Grand Master

89CAL

Posted
Posted

thanks mate, i need a fitting like that... if u can see in my sig photo, the rocker cover fitting on my rocker cover points upwards as they do standard and it makes my setup look a bit average.

Dont suppose anyone has one they want to sell to me?

ARTZ Grand Master

ARTZ

Posted
Posted
Another good trick is once you have the tip of the screw driver under the rubber and can prise it up spray some WD40 into the opening. This will help to soften the hose and allow you to get the screw driver in further to brake the seal between the hose and the pipe.

I would not put hot water anywhere near this area as it would run down over the coilpacks and the spark plugs.

So how do you wash your engine...? I use a hose...

hose pliers! and they have saved my knuckles more damage than any other tool I own

i really need to start that...."cool tools for skylines thread"....there's more where they came from!

+1 for cool tools thread..Its a great idea... :D

Got the hose off using a hair dryer, worked like a charm :(

Would've used hose pliers but couldn't find any today. :(

Bunnings and Supercheap didn't have them

I also tried to buy some today ,bursons said no...:(

I was using a hair dryer to dry paint the other day when i thought of it. .Hadnt actually tried it yet but glad it worked for you..

GF knows if she cant find her hair dryer its usually in the shed...lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • lilley's gtr
      Rb26/30 build

      By lilley's gtr · Posted

      I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani Refurbed astra pump thats the cover for it in the boot I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
    • lilley's gtr
      Rb26/30 build advice on pros and cons

      By lilley's gtr · Posted

      I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
    • Sleepergm
      Nismo rear spats

      By Sleepergm · Posted

      lol no cats running str pipes … might put the high flow back on but I suspect it might effect my ignition timing a bit. 
    • MBS206
      Nismo rear spats

      By MBS206 · Posted

      That looks a bit like yellowing to me. If the rear bar was looking like that from rich idle, I'd ask the question, do you have a catalytic converter fitted, and fully working?
    • RA708
      G'day!

      By RA708 · Posted

      Oh yeah gets really bad down here. I’ll have to upgrade the heater and wind screen wipers as well for optimal performance.
×
×
  • Create New...