Jump to content
SAU Community

Recommended Posts

Hi Guys,

There was abit of a carshow in Rocky on the weekend, with a dyno set up. So I put mine on for a run to check air fuel ratios, and here are the results.

1277106745.jpg

As you can see, run 1 made 341rwhp, a/f's were all fine.

Ran it up a second time, car was following pretty much the exact same line, went 337rwhp... but the a/f's went haywire. The operator wasn't keen to run it up again. His first thoughts were the lambda had fallen out of the exhaust. Apparently tho, this was not the case.

I'm pretty much wondering what you guys think. If it really leaned out that hard, surely it would start making more power (considering its on the rich side of things) before it leaned out wayyyyyy too much and started to detonate and lose power. The fact it follows the exact power of the first run kinda says to me its an error with the lambda, and not a problem with fuel delivery in my car.

Car has a walbro pump (i know i know), nismo 550's and a nismo FPR.

Surely a dying fuel pump would be more 'progressive' then the almost verticle climb of the a/f's on the second run? blocked injector?

Any ideas or comments would be great!

Edited by Granthem
Link to comment
https://www.sau.com.au/forums/topic/325708-massive-lean-out/
Share on other sites

your idea seems reasonable, such a drastic change in AFR

given its a dyno day and the sensor is moved around a lot, it might be a bit whacko or something

for such a dramatic change in AFR, i would have expected wonky power curve, detonation

wont always knock from that but i'd expect a decent loss in power at least. +1 for incorrect reading, only way to be sure tho is to check it a few times with another sensor

Edited by JonnoHR31
your idea seems reasonable, such a drastic change in AFR

given its a dyno day and the sensor is moved around a lot, it might be a bit whacko or something

for such a dramatic change in AFR, i would have expected wonky power curve, detonation

That's what I was expecting aswell.

Walbro pump.

Exactly what mine did around 260rwkw.

Was yours a "Mt Everest" like mine. I always pictured a more progressive leaning out when a pump slowly starts karking it?

wont always knock from that but i'd expect a decent loss in power at least. +1 for incorrect reading, only way to be sure tho is to check it a few times with another sensor

Hmmm yeh. There is another dyno in town, might be worth throwing it on theirs for a check up. They have always been ridicuously safe. I thought a pump would show on both runs, not just rear its ugly head on the second run... at least I'm hoping!

Check it on another dyno to make sure it is the car, if the A/F sensor is on its way out they default to 14.5:1 so it could be a failing A/F sensor, that curve is also very common in such a scenario.

Check it on another dyno to make sure it is the car, if the A/F sensor is on its way out they default to 14.5:1 so it could be a failing A/F sensor, that curve is also very common in such a scenario.

Very interesting Trent. Thank you very much! I'll look into another run on a different dyno

Haha yeh, I'll upload the graph with the boost curve tomorrow. Its on 14psi :)

Another question - Ramp Rate - how much does it affect things?

On the 3 times its been on a dyno, every operator has chosen a different ramp rate.

Godzilla - 100@150 = 337.1rwhp

Prodyno (first comp) - 100@140 = 337.7rwhp

Prodyno (most recent graph) - 100@200 = 341.1rwhp

Well its not going to be your O2 sensor because that has stuff all to do with the afrs at the top end. Have you at least got your Walbro wired for full voltage? Stick a fuel pressure guage in after the fpr and see what it reads at high revs next time you're on a dyno. (My tuner uses two O2 sensors - one in an extra boss on the downpipe and one in the tail pipe).

Out of curiousity could you post up the boost graph on the 14psi? Would be interested to see how it looks as mine really has trouble holding lower boost levels. Is yours just setup to 14psi from the adjustable actuator?

Edited by PM-R33

For it to have almost exactly the same power curve and the AFM to be all over the place, surely its the dyno not the car.

The power doesnt even change and seeing at A/F ratios have a HUGE impact on power the curve should have changed is some way.

Out of curiousity could you post up the boost graph on the 14psi? Would be interested to see how it looks as mine really has trouble holding lower boost levels. Is yours just setup to 14psi from the adjustable actuator?

Sure mate. I will post up the dyno with the boost graph. I have one from Godzilla and one from the other day. They didnt start the boost graph until it was already on boost so its just a flat-ish line.

Mine no longer uses the HKS actuator. It uses a garrett 14psi actuator, so it hold fairly nicely.

Well its not going to be your O2 sensor because that has stuff all to do with the afrs at the top end. Have you at least got your Walbro wired for full voltage? Stick a fuel pressure guage in after the fpr and see what it reads at high revs next time you're on a dyno. (My tuner uses two O2 sensors - one in an extra boss on the downpipe and one in the tail pipe).

I have a Greddy Fuel Pressure Gauge, reads around 3.5-3.6 bar at full noise (2 bar idle).

Unless its a track car, i would be leaning those out for sure

Its a street car... I wouldnt mind getting abit more HP out of it, and some more fuel economy :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...