Jump to content
SAU Community

Recommended Posts

i had my r33 gtst tuned at Unigroup engineering sydney and made 254kw atw with GCG high flow. When the car was getting tuned it developed a miss at 240kw mark. The boys gapped my plugs down to .65 to resolve the issue and then pumped out 254kw. My stock coils are very old and have been siliconed by some one at some stage.

Sourced some used splitfires from the SAU forums and then regapped my plugs to .95. Installed everthing and then went for a drive.

What a difference....... more response, crisp acceleration, pulls harder in the high rpm mark, definately gained a measurable differnce without a single miss in the rev range. Car breaks traction easier.

I recommend splitfires to anyone who has old coils, you can run a bigger gap with plugs and you will feel the difference

Worth ever cent

Wihout wishing to knock Splitfires all you are really saying is "if your coils are stuffed putting new ones in will make your car run better".

What would be more useful to know is stories of failures. We know that the Nissan coils are good for around 15 years (and I have seen two examples recently of people who have forked out for new stockers on the strength of this i guess) so it would be good to know how long before Splitfires, Yellowjackets, DSRs and other aftermarket coils start failing.

Yavus is a champ! You need to take the car back to him and get him to whack it back on the dyno to see the difference in horse power and overlay the power curve with the old one when it was tuned.

Then post the results. That would make this thread worth reading for a alot of people im sure.

Wihout wishing to knock Splitfires all you are really saying is "if your coils are stuffed putting new ones in will make your car run better".

What would be more useful to know is stories of failures. We know that the Nissan coils are good for around 15 years (and I have seen two examples recently of people who have forked out for new stockers on the strength of this i guess) so it would be good to know how long before Splitfires, Yellowjackets, DSRs and other aftermarket coils start failing.

How much are they new from Nissan I wonder, I have a bad misfire at the moment an I like your way of thinking.

How much are they new from Nissan I wonder, I have a bad misfire at the moment an I like your way of thinking.
Quite a bit! But it varies from dealer to dealer. You need to lnow someone who can get trade prices to get you a quote.

Yay for missfires!

I've got another question to throw into the bunch; I've always heard when people are recommending spitfires that they are designed for a higher boost (1bar/14psi >) where standards are designed for a lower boost setting like near standard (7psi).

Is this true? Or do you think it is more due to the stock coils age?

Geoff - If your not sure, tube a short video, I'm sure someone could confirm if what you hearing of a morning is a missfire or not.

The car sounds like a machine gun and makes popping/farting sounds.

My car pop pretty often when I shift from 1-2-3. Is that considered misfiring? It sound like any other rb and doesnt feel theres a loss of power too.

PM-R33:

i think just about every owner of a skyline over 10 years old has experienced misfire from coil failure, i'm no exception. when mine failed it would behave exactly like yours is in the video. my flatmate is a mechanic and he says the coils can be bench tested to isolate the bad coil but im skeptical of this because if the spark is earthing out through the casting into the head then (in my mind) bench testing might not emulate these conditions. chances are its only one playing up - for now. but if you just replace one and the rest are still old then sooner or later the others become likely to fail also, so for complete piece of mind you'd get a whole new set.

also a note to all: if your getting misfire, you'll probably notice it gets far worse as you run more boost, and i've been told misfiring is a good way to destroy your engine's bearings. so if you get misfire, wind your boost right down and gap your plugs down, and stay off the boost as much as you can until you get it sorted out.

anyone got stories on why to buy $600 splitfires over $400 yellow jackets? nissan parts dealer wanted almost $1200 for new coilpacks, its madness. have to say though, from what ive read they're probably the best of the options...

i had a bad missfire and the car was pretty much undrivable towards the end of my last plugs (coppers) life. it was really, really bad. changed to 0.8 gapped fr7dp bosch platinums and problem is mostly solved. i have to get new coilpacks, but uni is insane atm and i only work part time so coughnig out a few hundred on coils is difficult (till i sell the kart :bunny:), so heading to bunnings for some silicon!

PM-R33:

i think just about every owner of a skyline over 10 years old has experienced misfire from coil failure, i'm no exception. when mine failed it would behave exactly like yours is in the video. my flatmate is a mechanic and he says the coils can be bench tested to isolate the bad coil but im skeptical of this because if the spark is earthing out through the casting into the head then (in my mind) bench testing might not emulate these conditions. chances are its only one playing up - for now. but if you just replace one and the rest are still old then sooner or later the others become likely to fail also, so for complete piece of mind you'd get a whole new set.

also a note to all: if your getting misfire, you'll probably notice it gets far worse as you run more boost, and i've been told misfiring is a good way to destroy your engine's bearings. so if you get misfire, wind your boost right down and gap your plugs down, and stay off the boost as much as you can until you get it sorted out.

Really? Im still on my 15yr old coils and I have never had a missfire issue. I'm also running 16psi from a 35R, and still no issues.

I'm of the mentality that "if it aint broke, dont fix it". When and IF they fail, thats when they will be replaced by splitfires :bunny:

r33cruiser: im not gunna lie, thats impressive, i didnt mean to imply every coil pack dies on their 10th birthday. but it seems from my experience and almost all others ive known of have failed to some extent between 10-15 years. i'd say your rather fortunate to still be on original coils especially at 16psi without issues. what plug gap do you use?

yea it would be interesting to see the return/failure rate from yellow jackets vs splitfires vs the no name ones that come out of china. to be fair though the stock ones last 10-15 years in general and assuming thats when most of them were replaced (r32) with something else that gives almost all of the new ones still another while before they should be breaking down again. i've heard of one yellow jacket failing a week or so from new but no other failures from my knowledge. split fire has supposed "comparison" dyno charts on their website to show back to back results comparing their coils to oem ones but i dont really trust them as of course they probably handicapped the tune with the oem coils. i have seen one independent back to back dyno test done in nz between the split fires and the chinese red ones, 0.1kw difference atw on a 500hp gtr.. but your not likely to get exactly the same reading each time on the dyno so one might say absolutely no difference.

Edited by jonboy
PM-R33:

i think just about every owner of a skyline over 10 years old has experienced misfire from coil failure, i'm no exception. when mine failed it would behave exactly like yours is in the video. my flatmate is a mechanic and he says the coils can be bench tested to isolate the bad coil but im skeptical of this because if the spark is earthing out through the casting into the head then (in my mind) bench testing might not emulate these conditions. chances are its only one playing up - for now. but if you just replace one and the rest are still old then sooner or later the others become likely to fail also, so for complete piece of mind you'd get a whole new set.

also a note to all: if your getting misfire, you'll probably notice it gets far worse as you run more boost, and i've been told misfiring is a good way to destroy your engine's bearings. so if you get misfire, wind your boost right down and gap your plugs down, and stay off the boost as much as you can until you get it sorted out.

Ohh dude, that aint me/my car in that video I posted (if you notice its a R32/RB20). That's just some random video on youtube that I found lol.

I am well aware on what a missfire is and how to fix it.

Edited by PM-R33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah. OK. I take it back. I hadn't looked closely at the R33/4 arms and presumed that GKTech did as GKTech do everywhere else, which is to use sphericals there. The poly bushings are made to be 100% interchangeable, should use the standard bolt just fine. Every other bush in every other place in pretty much every other car, does.
    • @silviaz Ok cool, so much easier with a video. I can see why this video would be confusing for new players.   It is obvious that this entire bonnet is going to be resprayed, have a look in the background around 2:05, you can see a bunch of bare metal on the left side of the bonnet.  It's not an issue for the primer being laid down on the non-prepped clear on the bonnet. It will be sanded off at a later stage.  This might not be obvious to new players, but working on bare metal and factory paint in this instance, the factory paint is like a mountain and the bare metal is a huge valley. The bonnet needs to be levelled flat before it receives it's final stage of colour and clear coat. During this levelling process, the primer that is landing on the clear that you are worried about will be removed.  Also, this guy is out of control. Zero PPE while spraying, maybe he is a good example overall about what not to do lol.
    • Ok I FINALLY found a video lol. This took way longer than it should have as I could have sworn I saw multiple videos like this. I kept finding the completely opposite (the correct way of doing this). I wouldn't be surprised if I f**ked this up somehow.  I just realised where I've been getting confused and even with other things I work on. I haven't been doing things the regular way instead I'm going a roundabout way of doing things, like putting epoxy primer first then filler for example instead of putting just filler then primer on top of that, then wondering what happens if I get that primer on the clear coat that I haven't sanded yet. This was a bit of an epiphany 😂  But anyways, here this video. Time stamp, 2:56, some of the primer lands on the paint unscuffed above. You can see from the reflection it looks shiny.  
    • It does, this part circled in red. I assume the OEM bolt might not work well with the poly bushing because the dimensions may be different?
    • The J arm doesn't have bushes either. Assuming that by "J arm" you mean the part of the upright that runs down from the upper arm's outer bushes to the top of the hub. That has a kingpin style bearing in it. If you meant the lower control arm, it has 1 bush, at its inner end. If you have PU in there, that is superior to Nismo rubber. If you meant the caster/tension rod - it has 1x bush at the front end, and again PU is superior to Nismo rubber. But as I said above, I would definitely get the GKTech arms for that, as sphericals slay all other options there.
×
×
  • Create New...