Jump to content
SAU Community

Recommended Posts

  • Replies 129
  • Created
  • Last Reply

Top Posters In This Topic

We noticed a massive increase in midrange switching from PowerFC to Nistune (same tuner) on an S15. Nistune is ftw.

should be no "real" difference, but ultimately there will be a smidge unless you swap each timing mark across and load point exactly (same with fuelling).

We have done a few swaps between the two as well and to TBH its around 50 / 50 and always within a smidge of each other.

bout the only ecu i find has bigger variances is the Microtech due to the way it manages timing in the software.

Getting Nistune(d) by Trent this Saturday... Can't wait!!!!!!!!

Had a mate go to Chasers (Paul) last week and he seems to be happy with his tune. Though I've heard more bad about Chasers as well. Never heard a bad thing about Trent and his tuning abilities :D

Edited by blk15
should be no "real" difference, but ultimately there will be a smidge unless you swap each timing mark across and load point exactly (same with fuelling).

We have done a few swaps between the two as well and to TBH its around 50 / 50 and always within a smidge of each other.

bout the only ecu i find has bigger variances is the Microtech due to the way it manages timing in the software.

We had three different tuners tune the PowerFC on the S15 - Rob @ Sabaddin, Sam @ Dr Drift & yourself. No-one got it right. You might remember the car - stock looking white jap-spec S15 - made 245rwkw. A bit's changed now though.

Now with the Nistune is runs like a factory car. Cold start is perfect, return to idle after backing off throttle is perfect. The car's also making more peak power on the same boost. Why was the PowerFC so bad? It used to idle hunt like crazy, cold start was terrible, return to idle was terrible. That's all gone. Unless it was just a 'bad' PowerFC, I would never go near one on an SR. That goes for all the DET-conversion Pulsars I've been around with PowerFC's as well, same rubbish idle.

We had three different tuners tune the PowerFC on the S15 - Rob @ Sabaddin, Sam @ Dr Drift & yourself. No-one got it right. You might remember the car - stock looking white jap-spec S15 - made 245rwkw. A bit's changed now though.

Now with the Nistune is runs like a factory car. Cold start is perfect, return to idle after backing off throttle is perfect. The car's also making more peak power on the same boost. Why was the PowerFC so bad? It used to idle hunt like crazy, cold start was terrible, return to idle was terrible. That's all gone. Unless it was just a 'bad' PowerFC, I would never go near one on an SR. That goes for all the DET-conversion Pulsars I've been around with PowerFC's as well, same rubbish idle.

Yeah i do remember now, just after we opened it had a real bad case of PFC 'itis.

Most of the rubbish idles on pfc's are cause of the intake pipe and afm position..... but some pfc's dont care either way.. its weird, i think build number has a lot to do with it as the early serial numbers are way worse.

eep i hope my rb26 doesnt do that bad idle when i get pfc on :(

getting my exhaust on today.. cam gears / service done by GT hyper then i'll give you a call Trent :thumbsup:

Its an SR20 thing :P turbo snout and airbox are too close and custom intakes pipes create bad reversion older version PFC's hate it.

Car got tuned @ Status today!!! Very friendly/helpful, would definitely recommend them. Below are the results:

Year/Model: 01 Spec S (adm)

Engine/Size: 2.0 SR20DET

Turbo: t28 bush bearing

Power @ boost level: 185rwkw @ 15psi

Torque: 362.5 Nm

ECU: Nistune

Modifications: gktech fmic, fujitsubo exhaust, apexi intake, walbro fuel pump, turbotech mbc

My car initially made 162rwkw @ 14psi but was pinging its head off @ 14.5 AFR (massive black smoke at end of exhaust). I was really shocked and worried as trent could see.

But all is good now with the tune, sits nicely at 12AFR though the coilpacks are on the way out...

scan0002.jpg

scan0001.jpg

You can see it pinging (red)

Car now drives extremely smooth especially down low where it felt like a slug previously. Love the pull at around 3500rpm.

Thanks Trent for saving my engine :D

Edited by blk15
tbh the big thing for me is that Trent is a regular poster on the forums, and is happy to offer free advice, not saying anything bad about anyone else, but that shows a real commitment to customer service.

so when are you coming down from outerspace to get a tune?

meh im still sorting out whether I'll need a replacement dump pipe, gotta get AFM, new intercooler kit to fix up the boost leaks, and then I should be ready to get some Nistune love happening (i did have an insane thought of getting the Microtech retuned but yeah nah).

Don't think I'll be driving it from here to Melb again either lol (roads are like a rollercoaster until Bendigo!)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Literally looks like direct port nitrous haha
×
×
  • Create New...