Jump to content
SAU Community

Recommended Posts

hi guys, first things first, i have a psi guage, actualy in psi, and its the second one ive tried, and they both say psi.

now

my solonoid is out of the question, nothing runs to it at all nor is it plugged in, and i have the hose running straight to the actuator, im only getting 5 psi, i thought it might have been a leak in the system, but its a solid 5psi and dosent budge up or down when full throttling, if there was a leak the boost would drop slowly? or something

anyway, any ideas?

cheers

  • Replies 74
  • Created
  • Last Reply

Top Posters In This Topic

Standard turbo?

If so then yes, about 5psi is all you will get running straight off the actuator.

yea standard, i thought the actuator is 10 psi?

do i have to hook the solonoid back up to get 7-8psi?

alright so im gonna have to hook it back up and then, do the DIY for high boost all the time correct?

Could just buy an rb20 r32 actuator?

getting a little hard to find these days, I Think I have one in storage lol

Could just buy an rb20 r32 actuator?

getting a little hard to find these days, I Think I have one in storage lol

i dont really want to run 10psi, im not into the whole "must go faster" thing anymore, just would like the standard boost! 10psi = screwy mixtures etc since i just have the standard ecu

yea standard, i thought the actuator is 10 psi?

do i have to hook the solonoid back up to get 7-8psi?

No you just have to reconnect the bleed line to the bov return pipe and play with the diameter of the restrictor until you get the desired boost - bigger diameter = more boost. If you have lost the restrictor you can just solder up that branch of the T and drill the hole progressively bigger till you get the desired result.

Get a $30 tap and set it to 0.7 bar (8psi) yourself like I did. Better than stock IMO, more torque down low (obviously) and spools a little sooner.

The turbotech one on ebay is the one I have, well documented on this forum as to how good they are.

GL

Get a $30 tap and set it to 0.7 bar (8psi) yourself like I did. Better than stock IMO, more torque down low (obviously) and spools a little sooner.

The turbotech one on ebay is the one I have, well documented on this forum as to how good they are.

GL

if im not mistaken, the taps are quite unreliable, ive used them in the past and they cause boost creep issues...

to be clear

standard R33 GTST auto is 5psi

standard R33 GTST manual is 7psi

both have a boost scramble or "boost hi mode" which bleeds in another 2psi around 4500rpm from the standard solenoid

if you bypass the standard solenoid and do nothing else minimum boost for auto is 5psi and manual is 7psi

to be clear

standard R33 GTST auto is 5psi

standard R33 GTST manual is 7psi

both have a boost scramble or "boost hi mode" which bleeds in another 2psi around 4500rpm from the standard solenoid

if you bypass the standard solenoid and do nothing else minimum boost for auto is 5psi and manual is 7psi

my car is manual and its 5psi, hosed to the actuator

maybe your turbocharger failed and yours has been replaced with an auto turbocharger?

maybe your actuator has failed and your actuator has been replaced with an auto actuator?

maybe your car was auto and converted to manual?

unlikely but possible

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...