Jump to content
SAU Community

Recommended Posts

Hey.

So ive got a r33,rb25det..

Just installed bigger turbo,the closest i can compare to would be garret 3071r.

Power fc

external 38mm turbosmart ultragate

Z32 afm and 580cc injectors...

After a huge f**k around with getting it tuned,when i was assured i would have it back same day,it finally got done.

Got 326.6hp at wheels..boost is spiking at 18,and droping back to 15 by redline..

Quote for tune was $500,ended up costing $750.

Now after driving the car around for a few weeks,im noticing it kind of hesitates sometime when light on the throttle,seems to cold start fine,but then other random times it cranking over for 10sec or more and just coughing to life..hot or cold..

Also had to wind the boost down the other day as engine light had been flashing on,and was advised it was detonating..

I know the car's not perfect,but think it mite be worth my while getting the tune looked at by someone else..

Im living near newcastle..so anywhere around here or sydney..

Also any advise is also welcome

cheers

Edited by dilfukin
Link to comment
https://www.sau.com.au/forums/topic/331817-tuners/
Share on other sites

What turbo precisely? It seems like there is more to the story.

I would spend more time talking to your tuner before getting too far ahead. Ask more questions about why the car seems to be pinging, why it is hard to start etc.

If you have done this then what was their response?

Link to comment
https://www.sau.com.au/forums/topic/331817-tuners/#findComment-5384437
Share on other sites

yes common sense prevails here please

far too often we see people go get a tune, and any tiny isssue is a mega 6 page thread about the workshop being crap and a rip off before the guy spends 5 minutes talking to the workshop / tuner. please discuss with the workshop and let them address the issues. if you dont want to go back to them, goto another workshop for a 2nd opinion

Link to comment
https://www.sau.com.au/forums/topic/331817-tuners/#findComment-5384475
Share on other sites

have a look on your powerfc at the knock/detonation. mine never goes above 20 on 98 oct but when i have only been able to get 95 oct it has gone up to 60-80ish. think the light comes on at 100 or more from memory. make sure you have low numbers

Link to comment
https://www.sau.com.au/forums/topic/331817-tuners/#findComment-5384612
Share on other sites

turbo is a billet...i rang mr turbo on the goldcoast to try and track down the exact specs of the turbo,he said it would have similar spec wheels as a garrett 3071r... with .63 rear housing

I cant check knock as i dont have a hand controller for the computer,which was a problem in its self as tuner said his software wouldnt recognize my computer,saying it must be too old,so i borrowed a hand controller so he could tune it,which he did through the controller..

Boost is spiking because of crap bleed valve..two ways of fixing that is:1. another spring in the wastegate to run 18psi,or 2 get an electronic boost controller...?

Im not naming the tuner as i dont know for sure it's a tune problem....

Cheers

Edited by dilfukin
Link to comment
https://www.sau.com.au/forums/topic/331817-tuners/#findComment-5385639
Share on other sites

my GTR has to be tuned with the hand controller too, trust me my tuner HATES doing it with the hand controller but the datalogit doesnt connect with all POWER FC's. mine is an older model FC i think.

nothing wrong with tuning with the hand controller its just more time consuming and more fiddly going in and out of menu's

Link to comment
https://www.sau.com.au/forums/topic/331817-tuners/#findComment-5386844
Share on other sites

hand controller tuning is fine and has been the std for god knows how long?

its only in the last few years workshops have got onto datalogit as mainstream

datalogit makes it quicker and easier (less cost) and lets you be a bit more picky

but there would be hundreds of well setup quick cars with hand controller tunes

go back to the place who tuned it

Link to comment
https://www.sau.com.au/forums/topic/331817-tuners/#findComment-5386846
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...