Jump to content
SAU Community

Recommended Posts

i know all u guys think it pretty gay but i think it sounds pretty cool lol anyways so how do i actually get this noice the whole stu tu tu tu thing haha? i did some searching on here and found something about a pipe where does this pipe go? is there any piks of someone having one done?

block factory recirc valve (bov) and run a pod filter and you should get some good noise happening. As for perfecting pitch of the dose, well you need some TOOL to fabricate you a metal induction pipe to replace most of the rubber.

buy some pigeons. or a vl.

or just take off your bov and feel the joy of lag on gear changes while you impress all the hektic kebab spec vl owners with your epic dose.

The difference is almost negligble. Just sayin.

pls o please dont get this sound, im so un impressed with wankers who dose past me in their skylines, vls, supras and show off their hektic stu du du du du fagget alarm while thinking their cool...

just sayin

but if this is how you roll, as above.

i just think it sounds cool but as i said is there any piks? or anyone know about this pipe u need?

Do you have a pod filter or an airbox in the car? will be on the right side of the engine bay. It has been said already usually that pipe is plastic replace with with a steel one very easy to work out

Do you have a pod filter or an airbox in the car? will be on the right side of the engine bay. It has been said already usually that pipe is plastic replace with with a steel one very easy to work out

yeh man have a pod filter . which pipe u talkin about? my pod goes directly onto my afm

I prefer the Shetland Pony bov.

when crammed in your back seat, windows down, and jabbed with a Parker Ball point pen at the exact same time as gearchanges, it makes the best neigh/flutter/wastegate chatter noise.

I have 2 for sale if you are interested.

but you will have to get your own pen.

pics attached.

http://www.visitshetland.com/images/dp/uns...ony-enlarge.jpg

http://www.dkimages.com/discover/previews/876/65003527.JPG

Plain brown one makes the sickest sound..

especially if I draw blood upon pen jabbing.

Just purse your lips as if you're going to whistle, then make the UUUUUUUUUU sound. Repeatedly jab your tongue to your palate just behind your top teeth and PRESTO! You have your foolly Sik VL dose.

Cost farkall too. :P

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...