Jump to content
SAU Community

Hel Stainless Steel Braided Clutch Line Group Buy


Recommended Posts

  • Replies 187
  • Created
  • Last Reply

Top Posters In This Topic

Cheers man.

Pintaline is going to wait for the next one (good man!) so that's that sorted.

They are all packaged and ready to send tomorrow so every one should have them by Friday since it is going with Express Post.

Just a reminder to the GTT boys, I got you guys GTST clutch lines so please let me know if they fit (99% sure they will) so I can inform Hel to add the GTT to their list.

Awesome, thanks for letting me know guys.

It's fairly easy to do yourself, most annoying thing is bleeding it.

Just once again, let me know if they fit.

The clutch lines are unknown.

Hey buddy, do you currently have any leftover braided brake lines kits for R33 gtst,

Im interested in getting a set from you. Ebay is selling them for $175 deliverd to your door

How much can you get them for..

thanks mate

Edited by manuel

Hi Phil,

Do you plan on running the clutch and brake line and sump bolt group buys again if there is enough interest?

  • 4 weeks later...
  • 3 weeks later...

I will be doing an order with them in the next week because we need some lines for our Wilwood group buy. So I will message you before I place the order to see if you are still keen.

Got the line installed but just to let everyone know, you gotta modifiy the fitting a little to make it fit. According to Dan (the mechanic that does all my work) the banjo is at an angle which will cause abrasion. Thats for the 33GTR.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...