Jump to content
SAU Community

Recommended Posts

Hey guys,

I've giving up trying to figure it out and searching because most people seem to know.

I bought my car with 109k kms on the clock, but I have no idea what the numskull (censored) ex-owner did to it. I know he put 3 different brans of tyre on the car all at once and he had all the tyre pressures at 26psi, he had never done an oil change and relied on his mechanic to service it without questioning the products he used, he had no idea how much power had stock, or how much boost it was meant to run, or that the snorkel was missing, or that the brake rotors were scratched, or that it had a viscous lsd...

Sorry, I'll stop now.

So how do I confirm he did the 100k km service knowing he'd been trying to sell the gtt for many months before I bought it? Should I just to the service anyway rather then finding out it hadn't been done when the timing belt goes?

The clutch is failing now at ~130k km, so thats not a good sign. Then again the guy was an old man and drove like one.

Thanks for the advice.

Link to comment
https://www.sau.com.au/forums/topic/336536-has-my-car-had-100k-km-service/
Share on other sites

Seeing as the timing belt usually gets changed at the 100k service, if it were done there should be a sticker or something in the engine bay saying it was changed. Should be stuck on the timing belt cover. Although all this could mean is that the timing belt was changed and nothing else :)

Not sure if the photo's going to work, never uploaded one before! If it does, you can see a whitish sticker on black plastic just behind the pipe at the front. Thats the sticker saying the belt was changed at 100k. :)

post-74434-1284286122_thumb.jpg

Edited by eiresgaus

I think i'm right in saying that lol! As my old car (mitsubishi) didn't have that kind of sticker until the belt was replaced, then it was put on. Guessing timing belts come with that sticker when they're bought?

Yeah at least now I KNOW when my car had a new belt put in lol

Yeah mine must have been done in Japan as I'm the first AUS owner so maybe thats what Nissan do when they get the genuine timing belt (it more then likely would come with the sticker)

Better safe than sorry!

A lot of people try to sell before the 100k mark, coz major service= $$$.

Some people overshoot the mark and then make it someone elses expensive problem.

urgh *cries*

I guess I'll buy the kudos 100k service kit. Is it hard to install? I'm handy with a spanner but not very experienced...

I wouldn't recommend doing it yourself if you haven't done one before - you mess it up - it's engine rebuild time - as has been witnessed by some people on this forum ...

Take it to a trusted mechanic ..

I wouldn't recommend doing it yourself if you haven't done one before - you mess it up - it's engine rebuild time - as has been witnessed by some people on this forum ...

Take it to a trusted mechanic ..

Cheers mate, will do. It's so annoying as a newbie, it's so often a case of "don't do it unless you've done it before". Not criticising you mate, just the world haha.

I have a mate who's ridiculously competent at this stuff, he's done it all before, I'll see if he's keen on a project day haha. Otherwise my local mechanics a pretty reliable guy, I'm just keen for the experience.

Hmmm the guy I bought mine off (fellow SAU'er) said and stated in the ad it was done. So I'm pretty sure mine is! Can anyone on here read Japanese? Mine's all 100,000kms with a bunch of Japanese characters!

Hmmm the guy I bought mine off (fellow SAU'er) said and stated in the ad it was done. So I'm pretty sure mine is! Can anyone on here read Japanese? Mine's all 100,000kms with a bunch of Japanese characters!

Come along to the event below (in my Sig) next month and there'll be a couple of guys available there!

that sticker is there from factory, telling you the belt must be changed at 100,000kms.

the fact is, if you dont have receipts proving it's been done, you really should get it done yourself. you just dont want that thing letting go.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...