Jump to content
SAU Community

Recommended Posts

I just changed my RB25DET injectors to 740cc Tomei injectors. I am having a really really heavy petrol smell when i drive/stop/idle my car, is this normal? its really heavy petrol smell, no joke............my whole house can smell it if i didnt close the door to the garage when i get home........ any other way to make it not smell that heavy?

DOesnt sound tuned properly if its running rich as hell.

Do you have a cat converter?

pretty sure i have a cat converter , i have to ask my mechanic about that man, if he tuned it running too rich..i probably need to ask him retune it.....i will give him a call tomorrow to make sure! thanks

The fuel indicates leaking injector seals. Leaked fuel vaporize and you smell it through the cabinet. It will likely to leak or leak more violently under high boost pressure.

The fuel indicates leaking injector seals. Leaked fuel vaporize and you smell it through the cabinet. It will likely to leak or leak more violently under high boost pressure.

haha that was freaky, didnt read the whole thread before posting.. identical thoughts just worded different!

The fuel indicates leaking injector seals. Leaked fuel vaporize and you smell it through the cabinet. It will likely to leak or leak more violently under high boost pressure.

i smell it in and out of my car...............driving me crazy man!! so smelly!!!!!!!!!

champ if it is leaking from the injectors, the smell could be the least of your worries if your still driving this vehicle.. fire is a mutha f*ka in your pride and joy

get it sorted asap.

fire? are you serious?lol........i need to wait till next mon or tues to get it check man but i still need to drive this beast to work tomorrow!

If fuel is absolutely pissing out at the injector (but we don't know where yet), it's possible fuel can get inside the injector plug and start a spark that will ignite the fuel in the enginebay.

If fuel is absolutely pissing out at the injector (but we don't know where yet), it's possible fuel can get inside the injector plug and start a spark that will ignite the fuel in the enginebay.

from what i see, there is no fuel/oil leaking around my injector......but i cant see some of them ...its inside the thing.......

If you paid a mechanic to install these injectors, you should take it back to him to find the source of the smell.

And yes, the smell is vapor. Vapor is the thing point in which fuel goes boom best.

If you paid a mechanic to install these injectors, you should take it back to him to find the source of the smell.

And yes, the smell is vapor. Vapor is the thing point in which fuel goes boom best.

yea taking it back tomorrow for them to check , i can smell it really heavy in my car as well.....not just outside the car :S

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...