Jump to content
SAU Community

Recommended Posts

pictures are a little close for me to tell how bad they are but id say the 1st you can buf out with a good clay and a substance like QUIXX SCRATCH REMOVER or if not to deep use Meguiar's ScratchX.

for scratch 2 you could use touch up paint from a car shop i think repco has little tubes of touch up paint like a nail polish tube for small scratches, since its down under the bumper you can use the brush from these to touch up the scratch and then once dried use a polish to buff it out and smooth it

from what i can see your paint is gloss black so a gloss black would work just dont use 2 much cus then it will seem obvious

your other option for both would be a car repair shop witch wil charge you about $600 for a full respray but take note the more you do this the more chips will look more obvious as once resanded and resprayed the new paint will chip easier, ask any panel beater and they will confirm

gibbo, try carmate.com.au for aftermarket

u may need a local shop to work on getting it to fit perfectly as i heard their kits arn't 100% flush fitment.

otherwise the yahoo japan auctions have plenty of parts

  • 2 weeks later...
your other option for both would be a car repair shop witch wil charge you about $600 for a full respray but take note the more you do this the more chips will look more obvious as once resanded and resprayed the new paint will chip easier, ask any panel beater and they will confirm

this is your best option. If they do it properly, it shouldnt chip easier.. They will need to use a fine sand paper to take the gloss off the whole bumper. Then patch the damaged parts with a tiny bit of bog or putty if necessary. Sand over the bog. Prime over the bog. Sand over the prime and then repaint the whole thing.

It shouldnt chip off easier if you pay $600 for it... Id be pissed if it did for that much.. Put it this way materials cost about $100 if that.. and its about 1 day labour.

used the quixx scratch repair....it didnt even take the lightest scratch off, completely useless

if the scratch is not to deep eg not reached the primer you can fix it using products like Quixx if its deep then you need a touch up paint pen

make sure you follow the instructions provided properly and you may even need to repeat the process a few times

found these instructions on their site :

Preparation:

Wash area to be applied to remove dirt and grease. Read instructions carefully. Test product on small concealed area first.

A. For MINOR scratches (e.g. car wash):

Apply QUIXX Finish (No. 2) to the scratched area. Polish it with a clean cotton cloth in a circular motion applying some pressure to a mirror finish.

B. For normal scratches:

Step 1: Apply QUIXX Repair Polish (No. 1) to the scratched area and polish it for about 1-2 minutes with a clean cotton cloth in a circular motion applying pressure. Remove residues with a damp cloth.

Step 2: Polish the worked areas and any matt patches with QUIXX Finish (No. 2) to a mirror finish.

C. For deep scratches (e.g. scrapes):

First wet-sand the scratched area gently with little pressure for about 10 sec. by using the enclosed special sandpaper (grain 3000) with water. CAUTION: Do not remove all paint or clear coat! Do not expose primer! Follow steps 1 and 2.

D. For extremely deep scratches (exposed primer) and stone impacts:

In this case, first use a suitable color corrective paint (touch-up paint pen)

and let it dry for about 1 week. Follow the steps in C).

WARNING: Use according to instructions! Not suitable for extremely deep scratches exposing primer. If primer is exposed, first use a suitable colour corrective paint

it all depents how deep your scratch is but

let me know how it goes btw where did you get yours from?

got it from ebay...

gave it a go... honestly i think MAYBE it helped a little bit for the big scratches but i suppose it was never gonna do much on them... the little scratch it did jack all... probably wouldn't recommend

mjay can you link me your ebay purchase page - i think i might of gotten the from the same seller ,im suspecting i got a duped one maybe fake or lesser quality if you and i got from same seller.

on another note has anyone used scrach x 2.0 from meguairs? if so thoughts and exp with it??

Edited by ezy03
mjay can you link me your ebay purchase page - i think i might of gotten the from the same seller ,im suspecting i got a duped one maybe fake or lesser quality if you and i got from same seller.

on another note has anyone used scrach x 2.0 from meguairs? if so thoughts and exp with it??

boought it off ebay seller "High_Series"

i dont think mine was fake... honestly i jus think that the product is not really effective on scratches beyond the lightest scratch... i'm getting my car detailed by dr detail this week though so i didn't put too much effort in tryna get em out... i figure if he can't then i'll just touch up paint it

  • 3 weeks later...

Hi Mjay,

Not sure if you've fixed your car scratches. Sometimes it's worth getting the experts to do the job for you. I had great results with a local Sydney Northern Beaches mobile repairer. If you live in the local area you might want to try http://www.sydneymobilepaintrepair.com.au Certainly wont try the quixx scratch repair as you said it was useless.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...