Jump to content
SAU Community

Recommended Posts

Car has:

BLITZ 700cc injectors (most effiecient lag time of all 700cc injectors) $600

BLITZ K5-660r ($2800 new)

BLITZ D1GP manifold (made by their race department, not a buyable part) cost $2000new

BLITZ 47mm Gate with dual screamers. $1000 new

Mega responsive (full 22psi by 4000rpm) 400rwkw setup on BP98 @ 22psi, made 420rwkw on e85 before the injectors ran out, i envisage 460rwkw on E85 @ 22psi

$3800 no offers (if it doesn't sell it will go on my Aristo as i would rather keep it)

ATI 1000hp balancer and water pump pulley (200km old) $600

GREDDY oil Pump (200km old) $700 pics below

RB26 EAGLE H-beam rods $400

New Greddy coil-overs (setup for RB 12kg and 6kg) have original 8kg and 6kg springs too. $1200

Full R32 GTR rear Nismo Arm kit ( lower and traction arm all new) $400

Front s15 NISMO control arm (will fit r33 or if you want to widen track fit to s13 and r32 ) $250

Zenith guard bracing (extensive chassis strengthener) $250

rebuilt steering rack $100

Adjustable toe arms $100

Uras castor rods $200

Uras extra lock tie rods and spacers $200

Super Now tie rod ends $100

Nismo 2way 5000kms $800

R32 GTR cradle

5 bolt shafts not the weak 6 bolt

Str8 thru exhaust with twin rear bozuku flutes $150

oil cooler kit $200

Greddy 115mm intercooler ($2500 new) $600

Greddy radiator (r32 gtr) 1000 new $600

tomei fuel pump (sold) $350

Powerfc d-jetro and all sensors $1200

R34 GTT box bought with 17000kms $1500 can supply it as push or pull, currently setup as push (r33)

BLITZ twin plate (top of the range ORC) $1200

5 stud conversion, S15 front spindles, R32 gtr rear brakes, r33 front brakes, Blitz MR3 pads ($700 when new rear unused, front 80% left) whole lot $1200

whiteline sway bars adjustable front and rear $250

half cage suit sunroof $350

drift tacho and oil temp, oil press, water temp gauges $300

nardi steering wheel

vertical hydraulic handbrake with booster for one finger actuation (std still in place and working) $250

drift kevlar passenger seat with s13 rail $250

2 x sets 17x9 +15 uras ns02 all round with new toyo proxes 4 tyres $1500ea set

High Uras GT wing $200

Uras clear tailights $120

Genuine c-west bonnet $420

Super Made 180sx headlights (see pic) $150ono

much much more or take the lotl for $15k or will split over the next few weeks

IMG_3771.jpg

IMG_3772.jpg

th_catdyno21.jpg

20070522_330ab487e4fd94335bbeg8qPIp.jpg

Newengine001.jpg

Newengine019.jpg

IMG_3764.jpg

IMG_3765.jpg

Newengine006-1.jpg

headcomponentsferrea.jpg

sub2.jpg

ABCD0015.jpg

post-34927-1288352469_thumb.jpg

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

hey there how much u asking for the full turbo setup? and what turbo is it

$3800 no offers (if it doesn't sell it will go on my Aristo, its just to good to sell)

BLITZ K5-660r ($2800 new)

BLITZ D1GP manifold (made by their race department, not a buyable part) cost $2000new

BLITZ 47mm Gate with dual screamers. $1000 new

Mega responsive (full 22psi by 4000rpm) 400rwkw setup on BP98 @ 22psi, made 420rwkw on e85 before the injectors ran out, i envisage 460rwkw on E85 @ 22psi

Trent its andrew with red sil80 if you can, hold the guard braces and gtr subframe till i get back from japan if possible..... but if get buyer selll sell sell!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...