Jump to content
SAU Community

Recommended Posts

Car has:

BLITZ 700cc injectors (most effiecient lag time of all 700cc injectors) $600

BLITZ K5-660r ($2800 new)

BLITZ D1GP manifold (made by their race department, not a buyable part) cost $2000new

BLITZ 47mm Gate with dual screamers. $1000 new

Mega responsive (full 22psi by 4000rpm) 400rwkw setup on BP98 @ 22psi, made 420rwkw on e85 before the injectors ran out, i envisage 460rwkw on E85 @ 22psi

$3800 no offers (if it doesn't sell it will go on my Aristo as i would rather keep it)

ATI 1000hp balancer and water pump pulley (200km old) $600

GREDDY oil Pump (200km old) $700 pics below

RB26 EAGLE H-beam rods $400

New Greddy coil-overs (setup for RB 12kg and 6kg) have original 8kg and 6kg springs too. $1200

Full R32 GTR rear Nismo Arm kit ( lower and traction arm all new) $400

Front s15 NISMO control arm (will fit r33 or if you want to widen track fit to s13 and r32 ) $250

Zenith guard bracing (extensive chassis strengthener) $250

rebuilt steering rack $100

Adjustable toe arms $100

Uras castor rods $200

Uras extra lock tie rods and spacers $200

Super Now tie rod ends $100

Nismo 2way 5000kms $800

R32 GTR cradle

5 bolt shafts not the weak 6 bolt

Str8 thru exhaust with twin rear bozuku flutes $150

oil cooler kit $200

Greddy 115mm intercooler ($2500 new) $600

Greddy radiator (r32 gtr) 1000 new $600

tomei fuel pump (sold) $350

Powerfc d-jetro and all sensors $1200

R34 GTT box bought with 17000kms $1500 can supply it as push or pull, currently setup as push (r33)

BLITZ twin plate (top of the range ORC) $1200

5 stud conversion, S15 front spindles, R32 gtr rear brakes, r33 front brakes, Blitz MR3 pads ($700 when new rear unused, front 80% left) whole lot $1200

whiteline sway bars adjustable front and rear $250

half cage suit sunroof $350

drift tacho and oil temp, oil press, water temp gauges $300

nardi steering wheel

vertical hydraulic handbrake with booster for one finger actuation (std still in place and working) $250

drift kevlar passenger seat with s13 rail $250

2 x sets 17x9 +15 uras ns02 all round with new toyo proxes 4 tyres $1500ea set

High Uras GT wing $200

Uras clear tailights $120

Genuine c-west bonnet $420

Super Made 180sx headlights (see pic) $150ono

much much more or take the lotl for $15k or will split over the next few weeks

IMG_3771.jpg

IMG_3772.jpg

th_catdyno21.jpg

20070522_330ab487e4fd94335bbeg8qPIp.jpg

Newengine001.jpg

Newengine019.jpg

IMG_3764.jpg

IMG_3765.jpg

Newengine006-1.jpg

headcomponentsferrea.jpg

sub2.jpg

ABCD0015.jpg

post-34927-1288352469_thumb.jpg

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

hey there how much u asking for the full turbo setup? and what turbo is it

$3800 no offers (if it doesn't sell it will go on my Aristo, its just to good to sell)

BLITZ K5-660r ($2800 new)

BLITZ D1GP manifold (made by their race department, not a buyable part) cost $2000new

BLITZ 47mm Gate with dual screamers. $1000 new

Mega responsive (full 22psi by 4000rpm) 400rwkw setup on BP98 @ 22psi, made 420rwkw on e85 before the injectors ran out, i envisage 460rwkw on E85 @ 22psi

Trent its andrew with red sil80 if you can, hold the guard braces and gtr subframe till i get back from japan if possible..... but if get buyer selll sell sell!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
×
×
  • Create New...