Jump to content
SAU Community

Recommended Posts

haha im not going to install till the brake rotors arrive, then ill do brakes and suspension at once to save wheel removal time

i wish i could have done it tonight, had photo comp to go to instead

Let me know if you want some measurements for setup, might save you some time :) .

haha im not going to install till the brake rotors arrive, then ill do brakes and suspension at once to save wheel removal time

i wish i could have done it tonight, had photo comp to go to instead

what rotors you getting dude :?

*peaks interest*

dunno wtf duncan came from.. dyslexic with peoples names lately.. dale! lol :rofl2:

All good :) , don't you like my name? Last time it was "Greenieo" Lol!

Edited by Daleo
dunno wtf duncan came from.. dyslexic with peoples names lately.. dale! lol :rofl2:

:) Well I guess there are two Duncans in the Stagea forum.. Spose we just end up on peoples mind :)

Let me know if you want some measurements for setup, might save you some time :) .

ohh yes please! im going to set the height before i install them so i dont have to do it again.

also found out the spring rates, they are on the box. F 10kg / R 12kg

what rotors you getting dude :?

*peaks interest*

just slotted RDAs mate, nothing special!

ohh yes please! im going to set the height before i install them so i dont have to do it again.

also found out the spring rates, they are on the box. F 10kg / R 12kg

Pm sent.

Managed to pickup an Informeter Touch on the cheap from the States, unfortunately the seller only offered shipping within the USA - so Im proxy'ing it through 'ShipItTo'. Its arrived at one of ShipItTo's warehouses, so hopefully they'll send it out Friday their time (our overnight), and I'll get it Monday/Tuesday :P

Edited by Dunc
Nice one! Those parcel forwarding services are great!

I just received my Nismo stuff. VERY excited!!

Yeah I did some research before I decided to jump on to one, been pretty happy with the service so far. Its not exactly 'cheap' but it still works out cheaper than I can git one elsewhere; I guess they do have overheads & want to make a profit. Cant hate on them for that :P

Awesome stuff re: Nismo! You're all stocked up now! Have you ever done a power run on the dyno? Would be a nice 'look what I did in a weekend' power change :devil:

Nice one! Those parcel forwarding services are great!

I just received my Nismo stuff. VERY excited!!

cracking it open to have a look before you put it in or what? :P

Edited by Jetwreck
Yeah I did some research before I decided to jump on to one, been pretty happy with the service so far. Its not exactly 'cheap' but it still works out cheaper than I can git one elsewhere; I guess they do have overheads & want to make a profit. Cant hate on them for that :P

Awesome stuff re: Nismo! You're all stocked up now! Have you ever done a power run on the dyno? Would be a nice 'look what I did in a weekend' power change :)

you pay for the service! if it works for you, then it doesnt matter :)

cracking it open to have a look before you put it in or what? :devil:

sure will, ill take heaps of pics before i install it at 5pm :D

sure will, ill take heaps of pics before i install it at 5pm ;)

Good man! Will be interesting to see if theyve done the same thing as Impul on the main chip (in terms of covering it in gunk so it cant be easily re-read)

weird, its EXACTLY the same inside as the stock one. no mods appar visible..............

Basically confirms that its just a re-flash, not any sort of internal piggybacking etc. Good news of that being that if we ever have someone who can work on them locally they'd be able to read the Nismo ECU to get a starting point for tuning ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...