Jump to content
SAU Community

Recommended Posts

Just curious - has anyone had stuff sent over via containers from JPN?

I bought several things and asked Jesse to throw it all in the container to save on post...

He reckons I shuold avoid container at all cost due to no tracking # or insurance...

what do u think?

Just curious - has anyone had stuff sent over via containers from JPN?

I bought several things and asked Jesse to throw it all in the container to save on post...

He reckons I shuold avoid container at all cost due to no tracking # or insurance...

what do u think?

funny...he pushed me towards a container for my stuff!....but thats JDM's container!

yeah its JDM Garage's container...

So do I need to pay extra to get that stuff sent down from Brisbane since JDMGarage is in QLD?

that's gonna suck!!

yup....extra for shipping from Brisvegas. :(

Did he say if it's left yet.......I want my new stuff!

Edited by Jetwreck

Haven't washed mine in a week and a half... but I do drive dirt roads a little.

Good thing is that when it is dirty, it almost looks silver better lol

haha mine has probably a bit of dust after 2 weeks (due to a windy secure parking facility)

and its always just my luck to get rained on a day or two after i wash it >_< big dirty melbourne raindrops.

so far so good though!!

haha mine has probably a bit of dust after 2 weeks (due to a windy secure parking facility)

and its always just my luck to get rained on a day or two after i wash it >_< big dirty melbourne raindrops.

so far so good though!!

ive given up washing it for this season.

black, the slightest bit of rain looks like i drove door handle deep in mud lol

nah

  • front bar
  • quarter panel (drivers)
  • Headlight(drivers)
  • rad support fibre glass composite thing
  • radiator
  • fan
  • bonnet
  • maybe FMIC

but we didnt budget for more. so gave up. some beared man bought it. and was easily willing to pay MUCH more so no point

nah

  • front bar
  • quarter panel (drivers)
  • Headlight(drivers)
  • rad support fibre glass composite thing
  • radiator
  • fan
  • bonnet
  • maybe FMIC

but we didnt budget for more. so gave up. some beared man bought it. and was easily willing to pay MUCH more so no point

bloody Cam/Techno Viking!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...