Jump to content
SAU Community

Recommended Posts

Ok I've been searching for some time on the forums and while I have found some slight insight into what I am trying to find in terms of answers, I still have not found info related to what I require.

Firstly I own a NM35 Axis Autech Stagea. My first question is my fuel consumption high? I mostly do short trips (~6km) to and from work, not always everyday of week. Other than that just local city driving around chatswood sydney. The longest drives on a more regular basis are from Chatswood to Sydney CBD (think its only ~12km) but this is just for Nov mostly. And on fewer occasions I have done distances from Chatswood to manly beach (~20km). Those figure can double as they are one way. So recently I have been getting 18L/100km. But lately that went up a little (yesterday I was getting 20L/100km of 47km range). However I admit I do love to push the car so maybe its just my driving style?

Also can anyone tell me in the fuel usage history screen what each bar of the bar graph represents? Is it between each start of car, or the recorded range, etc? And how does the range figure work? I am not quite putting 2 and 2 together here.

Secondly - My car is still stock at the moment. If I am just crusing around and give half throttle to make the gear box kick back I feel nice, quick acceleration. Always put a smile on my face. But the same cant quite be said for full throttle. Maybe its because it has stock intake and exhaust so it cant breath as nice. But sometimes it feels like the car is limiting output to protect the gear box perhaps? I read other posts and I think there is such a thing as a torque converter to protect gearbox and keep it cool. Is this what I am noticing on full throttle? Or do I have a downgraded trans fluid thats making my auto gearbox under perform? OR maybe I am just experiencing wheel spin and dont know it. Couple time I have had all windows down in back street and heard the wheel just breaking traction. But I feel the lack of power on full throttle in more car/ecu controlled.

Well that's it. If anyone has info on those points and suggestions to maybe changes needed (trans fluid change, torque converters, etc) would be greatly appreciated.

My undestanding is you will go through a lot of fuel on very short trips as it will run very rich in the first few minutes until gets to working temp.

Have read that while full stationary warm up at low revs before driving of is in fact bad for engine, a 30 to 60 sec warm up could reduce fuel consumption as has started to warm up before placed under load.

Have achieved under 10L/100km on straight Hyw work and 13 to 15 for mainly 22km each way commute - country driving.

(Cringe expecting to be corrected before pressing "Add Reply")

Intake shouldn't be a problem althouigh a highflow filter for the stock airbox would be a good idea. Bigger turbo back exhaust definitely a good idea. I don't have an M35 but I believe the fly by wire accelerator is not as sharp as it could be.

Not to be a smart ass, but for 6km trips Id be recommending a pushbike, or something like a sachs madass or postie bike if you have a bike license.

Thats a lot of heating and cooling cycles for a big car, and I doubt it really gives the car a full chance to warm up.

Cheers to all for the feedback so far. Appreciate it.

I was not aware my car had a fly-by wire accelerator. Never occurred to me.

Yes 6km to work (12km round trip) is not much. But there is a small twisty section of road on the way where I lock it down into manual mode and OMG!!!! This car fly's! It definitely loves the twisty, windy roads which is much to my liking. I grew up racing through the Adelaide hills. Eagle on the hill was always a bench mark road.

I guess to be clear the "gutless" sensation when applying full throttle is most noticeable taking off from stand still or rolling start. Kind of get the feeling that half throttle is just as good but maybe its just me. Actually its probably just turbo lag I am starting to notice more as the weather seems to be heating up in preparation for summer. I just cant help but think there is maybe something I can do to make the gearbox more obedient to my driving style.

Oh yeah... Stupid me. It dawn on me today that my comments about my fuel consumption being high (20L/100km) could be to do with me using manual mode a lot more in the last 1-2weeks as I try to understand this laggy acceleration feeling. Plus its more fun :-)

It may be worth taking off the intake piping and intercooler, and cleaning out the sludge that has built up if you havent so far. The throttle body would need a clean as well.

This ensures at low throttle openings that the intake is flowing the amount of air that the engine and gearbox expects from a stock vehicle, so the shift points and behaviour of the gearbox is optimal.

This may help fuel economy but dont expect too much. Then again with around town driving, it may just help. A new O2 sensor is probably needed.

As for the difference between half and full throttle, it sounds normal to me. On every turbo car I have owned, the power output wasnt a linear relationship with the throttle opening.

Edited by zoomzoom

Hi Paul

The M35 has some odd settings for the throttle to keep it in line with the Cruiser it is designed to be.

Throttle will not open more than 30% till after 3000rpm. this is controlled by the ECU. Only solution to this is buy a Nismo ECU from Japan.

from standing starts full throttle will give you a worse start than a gradual application. When you go full throttle the butterfly opens only 30% but it dumps lots of fuel and causes a slower take off.

Fuel Usage History, each bar represents the fuel usage for the last time you reset on the fuel usage screen.

It uses the overall fuel history to determine the 'distance to empty".

As it gets warmer your fuel economy will get worse as the computer will use more fuel to maintain engine temps.

Cheers

Andy

Seems normal economy to me. I do short trips like u and I'm

About 20/100km and if i push it the trip computer can go as low as 3.7km to the liter.

Small trips means stop start normally. Eats fuel. When I do m5 runs out to other site I get better economy (6.5-7pm to the liter).

I dont know how you guys tolerate fuel usage around 20L/100km. I would expect that from a luxury behemoth Mercedes SUV around town but not a family oriented vehicle.

20L/100km would be considered a "worst case scenario". My long term average is around 11-12L/100km. but you can't flog the pants off it and expect Prius fuel economy. The car weighs 1700-1800kg (depending on model/spec) what exactly do you expect? :thumbsup:

I own a GSXR1000, this can get 4.5L/100km on the street. On the track this goes to 20L/100km. It's all down to throttle usage. :)

If you want to play, you have to pay.

You cant be riding that GSXR1000 like its meant to be at that fuel usage :)

I have a CBR1100xx and 6.5-7L/100km is my average street usage.

Lol, yeah, I know what you mean, I try to be good... I only said "can", not that it does vary often... :D My average is slightly less than yours, but my commute is mostly freeway.

Can't say I bought it to save on fuel... :thumbsup:

Edited by Daleo
Guys, Do you reckon he should reset the ECU so the transmission adapts changes, kick down characteristics to his driving?

Won't make a difference to the touchy kick down that the stock M35 has... no way of avoiding it if driving with a heavy foot, but if you have a controller right foot, a spacer kit will go a long way to giving the car an easier to control/predict kick down (don't have to walk on egg shells to avoid the kick down)

I find its not "touchy" enough (gearbox that is). well sometimes when not pushing it but if say i turn out a side street (rolling start) and i floor it its like, 1 sec.... 2 sec... oh! lets gear down a gear or two? not touchy enough. and in that instance i feel half throttle would have had me further down the road by then?

yeah think i should try some mods first. first id like to do the hdi fmic upgrade with thinner thermo fan. that should help at this time of yeah. i only got car nearly 3 months ago and maybe what i am noticing is summer arriving with increased turbo lag? after that exhuast. suggestions? 3 or 3.5 inch? not too loud either (thats a first).

so how do i reset ecu anyway? and recommended driving after reset before switching car off?

cheers!

ECU resetting is in the DIY section (in the stickies). Just drive it normally after a reset (it will learn)

Oh and squeezing the accelerator will give you more response rather than stomping on it :D

Edited by iamhe77
touchy on the stock ecu? try driving with a nismo ecu. if you even think about moving your foot it drops back a gear lol

lots of fun in the wet Iain especially at the roundabout just down the road from your place.

I just have to remember that I have a LSD and my car understeers in the wet when I lift off.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...