Jump to content
SAU Community

Recommended Posts

Hey my Skyline sits way too high!!! want to sit about 12-14 cm

not buying new coilovers for 1k+

$650+ cheapest quote for getting lowered decent amount using springs (By a professional)

$300-$350 springs off ebay etc and maybe DIY(spring clamp $50 or so????)

2nd hand coilovers?? $600???? haven't seen any 4 sale

i know putting springs on original shocks can be bad and wear out your dampers but if Im lowering it to the heights i want will it be ok?

Brenton has done the timing belt on a quad cam engine, done engine swaps, replaced head gaskets etc so he is pretty confident he could do it

links advice and being pointed in the right direction would be appreciated, thanks

Link to comment
https://www.sau.com.au/forums/topic/344178-my-skyline-sits-to-high/
Share on other sites

Swap suspension for coilovers is straightforward task really.

Just grab a set of coilovers, hell, you can adjust height if you're bored.

I may have a set of coilovers for sale (currently have 5 sets and 4 of them are in garage floor...), is your rear fork or eyelet mount?

Anything to suit r33, Mr Count?

Yeeessss.....

One set is stuffed though, another set have slight knocking sound from rear left and fronts live in my R now, will need to take them out.

You planning on rebuild the coilover or just whack it on?

PM me if you want them.

/Selling products shamelessly in someones thread.

Hamish, wow.................

old1.jpg

Nice spoiler bahahahahahahahahaha

Anything to suit r33, Mr Count?

I'm gona be selling my coil overs hsd tt less than 10000kms done with them lemme know if of interest can come for a spin feel what they are like.

Sadly this is what it sits at now. I had the suspension looked over by a mechanics in St Albans/Sunshine area when I first got the car and his jaw almost hit the ground...he was disgusted by how high it was....and I'm stick of it being called a silver commodore

Below are pics of the current ride height.

To the bottom of the stock skirt is 24cm and to bottom of door sill is 28. something. All unladen.

post-75520-1289706960_thumb.jpg

post-75520-1289706975_thumb.jpg

post-75520-1289706996_thumb.jpg

If you're not going to bother lowering it properly (at minimum lowered springs with properly matched shocks, or better yet coilovers) then don't bother to lower it until you can afford to. Chuck lowered springs on stock shocks and you're not likely to be in for a pleasant ride. Think about it - you're now asking the stock, old, worn-out shocks to work far outside the range the manufacturer intended.

yes and no.... i'd say that the RSR springs i had gave a pretty good ride juliette.... clearly i went for afterarket coilovers, but they actually weren't as bad as you might think

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...