Jump to content
SAU Community

Recommended Posts

Turbo M35's.

Can you please tell me how the single turbo is setup on your cars.

I am just curious as the whole thought of slapping a TT on the car seems silly if you can get a big single in there no worries. I think the 3.5 would handle a big single well with minimal lag.

So can you explain to me how they do it on your cars.

Is there a cross over pipe from one bank to the others?

Is the turbo mounted low in the bay??

etc etc.....

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/344279-m35-single-turbo-v6-setup/
Share on other sites

Turbo M35's.

Can you please tell me how the single turbo is setup on your cars.

I am just curious as the whole thought of slapping a TT on the car seems silly if you can get a big single in there no worries. I think the 3.5 would handle a big single well with minimal lag.

So can you explain to me how they do it on your cars.

Is there a cross over pipe from one bank to the others?

Is the turbo mounted low in the bay??

etc etc.....

Cheers.

The NM35 HAS a single turbo set up.

It's low down on the passengers side, and brings a balance pipe around the top of the bellhousing, joining into the passenger side manifold. The space is limited, and this compromises manifold design, and turbo size.

I would imagine the issue with twin turbos is interference from the steering column on the drivers side. Still, there are TT kits for 350Z, and the basic architecture in the engine bay is similar, so I'd be looking that way to begin with.

Edited by Daleo

I have a manifold here, I think it will bolt straight up to yours but the turbo is too small and I havent seen a bigger turbo that will come close to fitting.

If you wanted to go down the custom manifold route, a single gt30/35 on the lower passenger side should still work.

What are you thinking?

post-63525-1289739467_thumb.jpg

I have a manifold here, I think it will bolt straight up to yours but the turbo is too small and I havent seen a bigger turbo that will come close to fitting.

If you wanted to go down the custom manifold route, a single gt30/35 on the lower passenger side should still work.

What are you thinking?

It seems you are the most experienced in this. I was reading about the G 35 APS kit. I'm just thinking the most reliable easily accessible heat efficient option.

I'm sure you have covered every option out there. Feel free to fill me in on the positives and negatives on them.

The more I look into it. The more I feel Nissan didn't want this car modified.

Yeah, I think its been worked out that the VQ25 turbo set up would physically bolt on to a VQ35 straight up. But the turbo couldn't handle 3.5 litres of grunt :rolleyes:

When looking for turbo kits, you have to account for 2 things mate- 1, has to be able to fit a RHD, and 2, has to be able to fit a AWD. So what your looking for is a G35x turbo kit, that can be mounted for RHD. Have a look through this turbo kit site. I don't know where you would go for engine management, if you went down that path.

Alternatively, there is plenty of supercharged kits out there too! lots of options :blink:

Yeah, I think its been worked out that the VQ25 turbo set up would physically bolt on to a VQ35 straight up. But the turbo couldn't handle 3.5 litres of grunt :rolleyes:

When looking for turbo kits, you have to account for 2 things mate- 1, has to be able to fit a RHD, and 2, has to be able to fit a AWD. So what your looking for is a G35x turbo kit, that can be mounted for RHD. Have a look through this turbo kit site. I don't know where you would go for engine management, if you went down that path.

Alternatively, there is plenty of supercharged kits out there too! lots of options :blink:

Bejesus. Options galore. Thanks.

Anyone bought anything this expensive without being hit by massive tax at customs.

Bejesus. Options galore. Thanks.

Anyone bought anything this expensive without being hit by massive tax at customs.

Most of the kits dont have a very good manifold setup and you have to ditch the airbox on the single kits. It would be best to custom make a manifold for your choice of turbo and the new gtx Garrett turbos would be the pick atm. GTX 30 .82 in the stock vq25det location would flow enough I think.

Unfortunately the rods in the vq35de are thinner and weaker than the factory turbo rods, this is to help them rev. I would suggest new bearings, pistons and rods from the states before fitting any forced induction kit.

Unfortunately the rods in the vq35de are thinner and weaker than the factory turbo rods, this is to help them rev. I would suggest new bearings, pistons and rods from the states before fitting any forced induction kit.

Ok that makes sense. That's extra coin I hadn't counted on in the immediate future, but I guess that's why I am asking.

Cheers

Unfortunately the rods in the vq35de are thinner and weaker than the factory turbo rods, this is to help them rev. I would suggest new bearings, pistons and rods from the states before fitting any forced induction kit.

Thats why most of the kits seem to be set around 6 psi... some up to 8.5. Way below what the turbo's are actually capable of. If you were to do it, I guess mount up the twin kit, drive it and sort the gearbox while it makes 6 psi. Then when the banks recovered, go blow up the motor with some boost and rebuild with some capable internals :D

Either that go leave it NA and tune that way- which is easy too...

Anyway, parts for our cars mainly come out of the states- the G35 has a massive following.

If I had unlimited coin I'd buy just about everything here to make a high rev NA VQ35. Swappy gearbox to MT / RWD and reduce the weight... somehow :D

Every time I look at that inlet manifold I get a stir downstairs! :D

Bahh, engine driven superchargers are for pussies, unless theres a turbo in front of it... :D

The 6psi limit isn't because of weak rods, it is due to detonation as the stock compression is too high for FI. This can easily be rectified with E85, unfortunately the rods will break with the extra torque and when that happens there will be no resurrecting the engine.

Bahh, engine driven superchargers are for pussies, unless theres a turbo in front of it... :D

The 6psi limit isn't because of weak rods, it is due to detonation as the stock compression is too high for FI. This can easily be rectified with E85, unfortunately the rods will break with the extra torque and when that happens there will be no resurrecting the engine.

Actually, even the kits that lower comp to 8.5-8.8 keep the low pressure.... due to weak rods :D

i've see thicker drinking straws....

P1010284.jpg

From left to right: HR, VHR, and DE rods.

(nico club- US)

LAWL!! you got nothing to complain about:

Top: my QR25de rods - im pushing 10psi and 280hp through those :|

Bottom: SR20de rods

768400570_EfYkQ-L.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm so far behind in the jobs I have to do at both work and home (including car) that I have become immortal. There's simply no way that I can die now.
    • Each to their own I guess  Me, I put just as much time into cleaning inside of the cars as I do on the outside As for getting wet, it is really no different than steam cleaning the carpets at home, apart from the cars carpet dries alot faster than the house, again, I only do it in the hotter months and leave the car opened up for a few hours As I only do it yearly, it is just before I do the diff and gearbox service, so I clean the carpets, then it's up on stands, wheels off, service, clean the undercarriage,  grease the bushings and do a nut and bolt check on everything  Disclaimer: I typically had all the time in the world to kill when I was working 🤣, so spending a full day or 2 cleaning, serving and "looking at stuff" was,  easily achievable, and a fun mental therapy day As for time to kill, I retired last Wednesday, so apart from my physical training, my days are filled with lots of random jobs around the house and garden...."Idle hands are the Devils something something" I am also buying a new house sooner rather than later, I'm actually looking at a potential property tomorrow, I'm looking forward to getting a car hoist as I'm starting to get to old to crawl around under a car, I can only imagine all the undercarriage cleaning and looking at stuff when that gets set up
    • Yeah, I'm not interested in wetting the carpets, and I don't care about brown dirt/dust that lives deep in the pile or underneath. It's not like I crawl around on them in my birthday suit or eat dropped food off them (because there is never any open food in my car). The seats are alcantara (cheap Chinese imitation alcantara, to be sure!) with barely 1" of foam pad behind the surface. That's not getting wet either. Any car that I would be happy to get the interior wet, I would not care to put the effort into.
    • We have one that holds 2.8L of water. On floor carpet that hasn't been touched in 2 or 3 years, will take a minimum of 2 fills of the tank to do a bedroom, and that's going AROUND the bed.   In the cruiser, I used an ENTIRE 2.8L tank, just on the front passenger footwell. But it had some fungus growing, and had been full of mud from being used as a 4WD for many years. I can do that floor again, and it will still pull mud out. However, the water now only looks dirty, not pitch black and leaving full sludge in the bottom of the tank it sucks back into. Oh, and, this is about a $1500 unit.
    • This is mine, works a treat for the cars, suction is good, I use the Bissell clean and protect stuff I have found giving it a good spray and light scrub with the soft brush on the head of the nossle for carpet, and a rub with a microfibre for cloth seats and cloth door trims, prior to another quick spray before vacuuming it up works the best @GTSBoy You would surprised on what it gets out of carpet and seats that actually "look" clean, I recommend that you test drive yours when you have a little time to kill, then post pics of the muddy looking water that I believe you will find
×
×
  • Create New...