Jump to content
SAU Community

Recommended Posts

Whilst I think DRS is a bit hot and cold...tyres? I personally would like to see team do whatever they thing is best with regards to fuel loads, tyre wear, revs and hp etc. But you have to say the rules at the moment are working pretty good. Quicker cars can clear slower cars easier, yet normally they still have to race to get the job done with cars of similar pace

I figure when it gets to the point that teams wont run in qualifying there is something fundamentally wrong with either the tyre design or the allocation or both. Plus it makes Pirelli look like muppets which must be wonderful for them given how much coin they would be spending.

If they brought back refueling, i think you could give DRS the flick

Refueling.

I hate seeing every car driving 8sec off their quali time and then pacing themselves throughout the race.

You two are kidding surely? Refuelling is rubbish on the following grounds:

It costs squillions to cart all that crap around the world.

The car set ups are fundamentally less compromised as you dont need to make a car work on high & low fuel loads. which makes the racing more predictable.

The racing is even more dire as no one bothers over taking they just wait for the pit stops and pump in some quick laps.

Good trolling.

Quote someone without context & take the relative reference in the said quote & make it absolute.

Win, win. :thumbsup:

If in doubt quote the bit that suits and use it in your own context I say. (I am moving into federal politics next year btw.)

I unreservedly apologise for any misunderstanding and have assumed the position :spank:

The problem is the aero packages, not the cheap fixes. F1 would be more interesting given any new condition or rule or gadget, like having tyres last the whole race, that was briefly interesting lol. I think having two different tyres makes the racing great, it'd be better if people could take the gamble and one stop on the slower tyre, or 3-4 stop on the faster tyre, with both strategies finishing side by side. It'd fore more on track overtaking.

But while dirty air is the main problem with close fighting, bandaid fixes are all the fia seems to want to do. I mean wasn't it only 2-3 years ago that you had to be 3 seconds a lap faster than the car in front to pass? That was ridiculous...

Bit of trivia in the down time-

Q: Who is the second most successful GP engine manufacturer?

(answer may surprise)

http://en.m.wikipedia.org/wiki/Formula_One_engines

not really as Ford was cosworth up until it was sold in 2004ish

Is their really a lot of difference between a 'Honda' and a 'Mugen Honda'?

I remember reading the somewhat winding story about that connection a while back, but seem to remember it involves the Honda family and some drama/espionage. bit boring really.

Slightly surprising that merc comes in at 4th...

Edit: Just remembered McLaren wasn't always mercedes powered.

lolwut?

McLaren have had heeeaps of different engine suppliers.

Tidbit: Chrysler/Lamborghini almost ended up as an engine supplier, and the team built a modified MP4/8 to test their 3.5 V12 in

Erm, yeah about that... I do honestly wish I was watching cars that could follow eachother and properly duel, rather than all this dirty air crap. I do watch every race with my dad who constantly refers to the older years before I started following lol

^I was just reading about that (good old wiki). More tidbits: they went with Peugeot instead, but after a year of poor performance changed to the mercedes engines

Yes- Went from a 3.5L Ford-Cosworth V8 in '93 to a Peugeot V10 for '94; Which my McLaren history book tells me made 100hp more (740) from the same capacity than the V8 did.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...