Jump to content
SAU Community

Recommended Posts

  • Replies 174
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

You reckon the ultimate rear housing would be a divided tial s/s concoction? Im sure the tial v band s/s housings must have some benefits other then easy attachment to the manifold and stainless to retain thermal energy.

We've machined up a few rd blocks with the nitto 3.2 crank. the only feed back we've heard is 1 got under 8 seconds down the quarter (methanol nos 60psi and sohc, dedicated drag car)

You have been using RD28 blocks?

You have been using RD28 blocks?

Tuffer than a gtr500 block with ultra thick cylinder walls and extra webbing everywhere.

bit of dicking around to match to a twin cam head and about as heavy as a 30 block or even heavier but strong as all getup.

A mate has been thrashing the shit out of a 3.2 litre built on this block making over 700 at all 4 for 3 years or more. Bombproof!

Im pretty sure that most of that strength advantage of the RD28 block begins to dissapear once you start boring and stroking them. The only thing that would help a little is the external coolant return from the head near the back of the block on the right side.

The standard bore being 85mm does make the cylinders thicker, but in order to maintain coolant flow between the cylinders in the block, the OD of the sleeves is still around 92-93mm maximum. So 4mm cylinder wall thickness at best with a 85mm bore.

The ability to run the squirters would dissapear with larger strokes as well unless you were to slot the crankshaft like an OS giken crank, or like I did when fitting my modified RB30 crank to the RB26 block.

You have to clearence the sides of the block for the rods when the stroke is greatly increased. See the attached picture and how close the No3 rod bolts are to the side of the case, and the required case clearencing. This is an RD28 with a 90mm stroke. There will be 1mm clearence from the rod to the crankcase. The main caps are billet alloy and the main studs are offset drilled from the standard 10mm holes, to 14mm. The standard RD28 cradle wouldn't clear the 90mm crank.

Being in Australia its really hard to pass up on the RB30 block just for how easily they are obtained and adapted to an RB26 head. In my opinion, there are other opportinities such as sleeving that people should really consider a lot more befoer heading down the RD28 conversion path.

post-26553-0-52348900-1324201290_thumb.jpg

Ive seen that picture somewhere before. Very tough setup.

Possibly on the GTR UK forum. Its from an 8 second R32 GTR in Urkaine. He ran an 8.16 with this setup. A rod went through the side of the block though, and now a new engine is being built to replace it.

Possibly on the GTR UK forum. Its from an 8 second R32 GTR in Urkaine. He ran an 8.16 with this setup. A rod went through the side of the block though, and now a new engine is being built to replace it.

is the owner rebuilding another rd28 or making a switch to the rb30?

is the owner rebuilding another rd28 or making a switch to the rb30?

He's keeping the RD28 block and replicating what he had with some improvements. Availibility of the block is the main factor though. RD28 blocks are easier to source than RB30 are for him.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...