Jump to content
SAU Community

Recommended Posts

well send the request.. and ill add... im not lying about who i am?! thats pathetic..it was one of the admin guys... quite nice really... Robincooper? i think his username is....

You guys are way too trusting. Post a pic of you holding a piece of paper saying the date and "SAU virgins here you go"

Only then will I believe.

No trust necessary, just a good eye for evidence :)

anyway, I assume if burnouts are the start then does that mean it'll eventually become perhaps a drift/track car? i.e. useful for something else?

because when I was at the drags last week the burnout comp was between a VN commo wagon and an ED falcon...both stocko V6's worth maybe $500 each and they did a great job entertaining the crowd and popping tyres.

So really, I'd ditch the heavy manly $40k motor and get something light and fun because if you want to do anything other than burnouts it'll handle like a boat with a big fat front end...and basically anything with a peewee amount of power and an LSD can do a good enough burnout....AND...if you're just starting to do burnouts then why blow a crap load of money on something which may very well be harder to control and cause more pain when you hit the wall?

p.s. also looked you up on fb, but you're not a fan of mariah carey so I cannot add you :)

Must go for a drink one time! :cheers:

Sorry, I'm gay.

haha. smooth.....

that red coupe video has been around forever. take it from a 31 owner (no pun intended....), dont spend any money on 31s, they're just not worth it anymore.

I bought my R31 wagon for $500 with a cut and blocked rear brake line! Judging by the rubber in the guards, it didnt do too badly for something with a f**ked exhaust and god knows how many kms...

yer a cheap thrasher is good fun but the thought of 40k on 31 makes me sick

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...