Jump to content
SAU Community

Recommended Posts

Im being told that rb20's make power easier than 25's

Also that my mate has 270rwkw from his rb20det...

There was a thread created a while ago for people with rb20's making 260rwkw or more and all seemd to have trouble getting there

Just to confirm rb20's make less torque, have more turbo lag and as a genral make less power if the mods where the same for an rb25

?

Link to comment
https://www.sau.com.au/forums/topic/352824-rb20det-and-rb25det/
Share on other sites

Im being told that rb20's make power easier than 25's

No. A mate of mine has basically the same mods on his RB20DET as I have on my RB25DET. We both have upgraded turbos on stock manifolds, stock motors, aftermarket ECU and fuel system etc.

My car is tuned on BP98 at 17psi and makes 301wkw, same dyno his car tuned on 30% ethanol and 21psi makes 295kw. He gives me a bit of a run for my money on midrange torque - probably more to do with extra boost and better fuel, but his falls flat at 6000rpm and mine keeps making more power. On the same fuel and boost I have roughly 50kw on him, better off boost torque and way better midrange.

No comparison.

Il grab the list of mods and let you guys decide

apparently stock injectors, stock ecu.. 3incj zorst, fmic, 18psi, flat top pistons, to4e turbo and a tune making 256rwkw

il update if there are any mods i left out

Il grab the list of mods and let you guys decide

apparently stock injectors, stock ecu.. 3incj zorst, fmic, 18psi, flat top pistons, to4e turbo and a tune making 256rwkw

il update if there are any mods i left out

stock injectors would not let you produce that much power.

I've owned both RB20DET and RB25DET, for someone to say RB20DET makes more power easier than RB25DET mod for mod, they must be on drugs >_<

Mod for mod, the RB25DET will make more power easily, why on earth would R32 boys be putting RB25DET motors into their cars? Go figure!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...