Jump to content
SAU Community

Recommended Posts

Definitely less pokey. AC is fine since it was regassed just before I bought the car. Even with the hdi intercooler the heat really takes the oomph out of the engine. The difference was very discernible when we had the hot days early last week and the cooler last couple of days.

Link to comment
https://www.sau.com.au/forums/topic/352941-curious/#findComment-5657221
Share on other sites

The stock ecu drops timing out heavily on hot days and ramps up the fuel, its what Nissan had to do to save an engine that's being thrashed on a hot day. If you can lower the intake temp you wont notice it as much.

Link to comment
https://www.sau.com.au/forums/topic/352941-curious/#findComment-5657247
Share on other sites

So was the bigger intercooler suppose to help with the hot weather?

with the last 6-7 day's we have had in Sydney it would not matter what IC you had....you would still be see a considerable change in drivability!.....I'm just glad I no longer have my standard one!

Link to comment
https://www.sau.com.au/forums/topic/352941-curious/#findComment-5657535
Share on other sites

with the last 6-7 day's we have had in Sydney it would not matter what IC you had....you would still be see a considerable change in drivability!.....I'm just glad I no longer have my standard one!

Craig,,, You NEED water spray...... mmmwwwwwhhhhaaaaaaa :whistling:

Link to comment
https://www.sau.com.au/forums/topic/352941-curious/#findComment-5657614
Share on other sites

You can try a cooling spray on the IC. Jaycar have a kit.

On M35's the intake air temp sensor is in the AFM. You could put ice in the intercooler and the ECU would still see the same temperature. Ice in the airbox would work...

Link to comment
https://www.sau.com.au/forums/topic/352941-curious/#findComment-5657693
Share on other sites

Last time I checked dry ice made CO2... not combustible- but cold! So it would prob make a good combustion extinguisher! :thumbsup:

Maybe one of those massive dry ice chamber/intercoolers that the dyno cars/drag cars run!!!

Do they sell a Temperature Cut defender...?:rolleyes:

Link to comment
https://www.sau.com.au/forums/topic/352941-curious/#findComment-5657746
Share on other sites

On M35's the intake air temp sensor is in the AFM. You could put ice in the intercooler and the ECU would still see the same temperature. Ice in the airbox would work...

In the R33 manualon page EN13 it shows where the temp sensor is. It looks like it is in the T/B. I could be wrong, but if this is so a spray unit on the fmic would help in the C34s.

Edited by 66yostagea
Link to comment
https://www.sau.com.au/forums/topic/352941-curious/#findComment-5657880
Share on other sites

In the R33 manualon page EN13 it shows where the temp sensor is. It looks like it is in the T/B. I could be wrong, but if this is so a spray unit on the fmic would help in the C34s.

most definitely would work me thinks.....and probably quite well!

Link to comment
https://www.sau.com.au/forums/topic/352941-curious/#findComment-5657930
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • R34DE as in R34 with an RB25DE? So did you get this? Or you planning to?  I'm not really sure what you're saying. 
    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
×
×
  • Create New...