Jump to content
SAU Community

Recommended Posts

Hey all,

Got a bit of a dilemma.

My AFM's decided to give out on my R32 GTR and I am not sure what to replace them with. Is there a cheaper NEW alternative than going through Nissan for $850 each. There are Z32s but my car is completely standard and they are 80mm compared to the standard 65mm.

Do I just look at getting mine replaced with a second hand set or getting them repaired/cleaned.

Some advice would be great.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/355258-afms-alternative/
Share on other sites

if your car is stock stock dont get Z32s or Nismo's

it wont run as the car expects stock BNR32 AFMs

you should try to repair them or even a local elec repair place that does tv etc

it will just be a dry solder join on the connector or on the board

the vl commodore has the same problem when the plug dies

If u have a stock ecu etc tyen stay with stock afm's.

As above there is a diy repair on the afm's. Normally inside the black box part near the connector the solder joints dry out and crack causing non contact.

just in case you were somehow in doubt the best option is either get yours repaired or buy a pair of used standard ones. nismo ones would be the other option if you are planning more power down the track but they will not run with your standard ecu so you'd need to get an aftermarket ecu and a tune just to use them. so really a waste of time at this point. again just buy a used pair or get yours repaired.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...