Jump to content
SAU Community

R33 100K Complete Service Cost Enquiry

rehab2010
 Share

Recommended Posts

rehab2010 Proficient

rehab2010

Posted
Posted

Guys,

what can I expect to pay for a 100,000km service on the R33 Gt-R - it hasn't had the belts replaced, and the normal service is due too.

Anybody has any idea?

Also - anybody recommending any good shops in Melbourne, preferable on the east, south-east side to do the work.

rehab2010 Proficient

rehab2010

Posted
  • Author
Posted

should be looking at about $1k for everything.

best thing would be to call up

since its a gtr and your melb, i'd reccomend racepace but most decent shops should be able to help

you out

would 1K be with the replacement of the water pump, or just oils,filters, timing belt?

NISMO Grand Master

NISMO

Posted
Posted

Find what parts you need and do a bit of a dig around. Genuine RB26 water pumps for example can be bought for peanuts from the US. Same with most other parts.

Do this yourself and you'll save heaps just ask the shop of your choice what you need and go and get it.

Labour wise i would expect to pay around the $500 or so at most shops.

rehab2010 Proficient

rehab2010

Posted
  • Author
Posted

Find what parts you need and do a bit of a dig around. Genuine RB26 water pumps for example can be bought for peanuts from the US. Same with most other parts.

Do this yourself and you'll save heaps just ask the shop of your choice what you need and go and get it.

Labour wise i would expect to pay around the $500 or so at most shops.

Thanks for this advice - I'm thinking along the same lines - damn, 1K or 1.5K - that's a lotsa a coin.

KamikazeNinja34 Veteran

KamikazeNinja34

Posted
Posted

umm...not really...

Might be 1.5k if you don't have anything but drivetrain fluids to flush and replace and with engine oil change. Expect it to blow out exponentially if anything is wrong with the car. For example. Just had mine done and had to replace both o2 sensors (car was running very rich) and both rear brake pads. Parts alone for those 2 things added up to another 8-900 dollars. Plus more labour. Rb26 is a prick of a job from what I hear. 4wd fluid has to be changed. Transfer case fluid has to be changed. Hicas has to be checked... Etc. with the extra bits and bobs I actually had a good 2.5k ish to do that service. 1-1.5 is what I'd expect and have seen a normal 100 000 km service on a gtst cost. With nothin wrong with the car. It is expensive but well worth it.

Galois Veteran

Galois

Posted
Posted

kudos motorsport sells 100k service kits. I'd give them a call, andrew sullivan was a world of help for me.

ONLY GO TO A PERFORMANCE MECHANIC. And only one who has been recommended to you, or has a couple of gtr's sitting out front. Any old mechanic will say they can do the job, but you want it done right and you don't want to pay for them to learn.

rehab2010 Proficient

rehab2010

Posted
  • Author
Posted (edited)

kudos motorsport sells 100k service kits. I'd give them a call, andrew sullivan was a world of help for me.

ONLY GO TO A PERFORMANCE MECHANIC. And only one who has been recommended to you, or has a couple of gtr's sitting out front. Any old mechanic will say they can do the job, but you want it done right and you don't want to pay for them to learn.

I went to see a mechanic that usually works on the Porsches and Audi's - and had them do the job for me. They've done work on GT-R's before but they are not a PERFORMANCE shop as such. Then again, I had very famous performance shop suggest I use VMX80 in my tranny - so much for "performance" suggestions.

He got a whole kit for me, all brand new, timing belt, tensioner bearings, water pump, all the ancilliary belts, new battery and a coolant flush - all up just over 800.

Edited by rehab2010
Galois Veteran

Galois

Posted
Posted

800 for parts and labour? That's pretty amazing.

Point on mechanics is, plenty will say they can do the job, and have done the job, when that plainly isnt the case. There have been a lot of bad experiences documented on here

rehab2010 Proficient

rehab2010

Posted
  • Author
Posted

800 for parts and labour? That's pretty amazing.

Point on mechanics is, plenty will say they can do the job, and have done the job, when that plainly isnt the case. There have been a lot of bad experiences documented on here

correct - parts and labour. So far so good ;)

Galois Veteran

Galois

Posted
Posted

I got a $700 quote for labour, though the mechanic didn't know what he was doing, it's easy to get ripped. That was when I terrifyingly realised I had no proof the 100k service was done, and was going to get it redone just in case. Luckily I found the sticker hidden away under the engine bay just in time to cancel the ordered parts.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By GTSBoy · Posted

      That's hilariously putrid!
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • hardsteppa
      Hi everyone.

      By hardsteppa · Posted

      Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...