Jump to content
SAU Community

Recommended Posts

nah defo not trapped air in there.. have bled it properly til no bubbles coming out the bleed screw.

nothings changed either,.. and the problem has got worse over last few events so something is up

Get the gas test done on the coolant to confirm HG. It's the easiest way to rule it out.

With the problem getting progressively worse it seems pretty likely.

Running E85 is probably helping to keep your temps down as well....

Probably wouldn't hurt to under drive the water pump either.

Edited by badhairdave
  • Replies 80
  • Created
  • Last Reply

Top Posters In This Topic

I've had similar issues in the past with cheap radiators. My first one clogged up with shit and did the same as what you are describing.

Take the rad out, put a garden hose on one end and let it rip. If it flows fast, you have other problems, if it doesn't get a new rad. (Thanks to Trent for that)

done pressure test on radiator.. 15psi for 5 mins and no drop in pressure

comp tested with works ryco comp tester which does read lower then most

1: 90

2: 90

3: 90

4: 95

5: 95

6: 90

Shouldn't it read the same as most? If you have 90 compression, you have issues

Is it losing any water at all?

I had a headgasket issue last year, leaking into the cooling system it displaces the water and leaves you with air.. try getting it on dyno and watching the overflow tank when it hits boost. I did the same test you did by checking for leaks up to 20psi and it was fine while idling in the car park. Watch it come on boost though and suddenly the overflow tank starts bubbling violently.

If you haven't got a dyno to test on, just take the overflow pipe off the overflow tank and poke it outside the bonnet and go for a run. You'll soon see it go off like a pressure cooker.

Do you still have the factory oil cooler?

what are your oil temps doing?

I have the same issue with my CA, couldn't keep it cool even with a 150% thicker radiator (25mm R32 Vs' 10mm Standard CA). Once i fitted a oil cooler never had an issue again.

Mt theory is that the only way that the engine could get the heat out of the oil is through the coolant.

i have an aftermarket oil cooler (and still the OEM near the filter block) and oil temps reach 130 ish after hard laps.

not really losing water... it doesnt use it. it pushes it out the rad once boiling and doesnt suck it all back in.

i always thought that was typically an air leak ie pushes water out but sucks air back in, but you've had a pressure test. maybe the rad cap is the problem and letting water out but sucking air back in. HG as suspected might explain why the water is being displaced.

Edited by Scooby

You still havent answered the question as to what type/thickness FMIC youre running.

Have you made any effort to ensure all airflow actually travels through the rad ie sealing and cowling of the radiator to the rad support???? Same with the oil cooler?

Any type of cooler works 1000% better with ducting/cowling.

It appears the car is mostly used for drift??? You need to make the most of the little airflow you get...

Again a pressure test shows absolutely nothing about the cooling ability of the radiator.

sorry mate missed your post.

its a 400X300X76 core mounted right in front of the rad. reason for this was to run shorter cooler piping and have the cooler in a safer position then the tradiational fmic location.

i have made an alloy box section up also which directs aii the air coming in from the front bar thro the IC and rad.. the sides are blocked off so it is un able to go anywhere else.

183152_1764592067976_1034359196_1948264_812334_n.jpg

183608_10150098000211109_693631108_6607544_2048564_n.jpg

Well Snowy is running a triple pass PWR items ATM i believe. So far so good.

Looks like that front bar is smaller than the ducting?

Also what is on top where the rad support is? If there is no panel, all the air is gonna do is go that way as it'll look for least resistance.

Or simply go around the sides. Also how much room between I/C & Rad?

Perhaps just take a photo looking down onto it

What cooler is right @ the bottom of the I/C?

front bar and duct are a snug fit, same size. the sides are the same width as the rad.. air is forced thro the cooler and the rad. the IC is 5mm away from the radiator. no top panel. should probably make one up.

the little cooler at the bottom is a power steering cooler.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If they can dyno them, get them dyno'd, make sure they're not leaking, and if they look okay on the dyno and are performing relatively well, put them in the car.   If they're leaking oil etc, and you feel so inclined, open them up yourself and see what you can do to fix it. The main thing you're trying to do is replace the parts that perish, like seals. You're not attempting to change the valving. You might even be able to find somewhere that has the Tein parts/rebuild kit if you dig hard.
    • Can you also make sure the invoices on the box (And none exist in the boxes) are below our import duty limits... I jest, there's nothing I need to actually purchase and order in. (Unless you can find me a rear diff carrier, brand new, for stupidly cheap, that is for a Toyota Landcruiser, HZJ105R GXL, 2000 year model...)  
    • Murphy strikes again! Nothing at all would have gone wrong if you had the tool kit in the car! You'd have just found the clamp loose the next time you went to touch it...
    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
×
×
  • Create New...