Jump to content
SAU Community

Recommended Posts

Looks nice Dale!

Whats the final day to get payment in for the group buy? Just had to shell out to the politician's retirement fund, so hoping I can wait until next Thursday?

Here are some pics of the Heavy Duty mounts for the Sway Bars; 5mm extruded 316 Stainless Steel; won't rust, bend or fracture.thumbsup.gif

post-61153-0-82860600-1301888445_thumb.jpg post-61153-0-25156200-1301888484_thumb.jpg post-61153-0-32777900-1301888528_thumb.jpg

Or you could just use these...whistling.gif

post-61153-0-88487600-1301888745_thumb.jpg

ill be installing mine this week. they look fantastic!

I thought I had better check the sway bars on my ARX before giving these uprated ones further thought. Haven't found the handling the sort of rolly boat others describe and wondered if they might not be standard.

The back one is 24mm and the front 29mm (measured with rule but should be pretty close - checked with rule in front and behind the bar). Both have just the one hole each end. Does the ARX have a bigger rear sway bar standard? I had read it is only 18mm standard. The 29mm front would match the standard size.

How could you tell if the front is a stock hollow? Tap on it? Seams visible? Cut in half with hack saw? Other?

I thought I had better check the sway bars on my ARX before giving these uprated ones further thought. Haven't found the handling the sort of rolly boat others describe and wondered if they might not be standard.

The back one is 24mm and the front 29mm (measured with rule but should be pretty close - checked with rule in front and behind the bar). Both have just the one hole each end. Does the ARX have a bigger rear sway bar standard? I had read it is only 18mm standard. The 29mm front would match the standard size.

How could you tell if the front is a stock hollow? Tap on it? Seams visible? Cut in half with hack saw? Other?

They sound like the stock ones. From memory stock front is 30mm and rear is 24mm BUT they are hollow. So taping them nay give you the indication.

The GB ones are 32mm front and 27mm rear and both are solid so it is something like 70% stiffer than the factory ones.

They sound like the stock ones. From memory stock front is 30mm and rear is 24mm BUT they are hollow. So taping them nay give you the indication.

The GB ones are 32mm front and 27mm rear and both are solid so it is something like 70% stiffer than the factory ones.

Thanks. Will give tapping a try tomorrow.

Did more searching with some success for a change and found posts from 2008 where Sydneykid wrote yours was 18mm rear hollow and he replaced it with 24mm solid?

Anyone else checked what is on their ARX?

Thanks. Will give tapping a try tomorrow.

Its not as easy as tapping, but there is a massive weight difference. just another way...

Find some corners and pitch it in - you'll find the barge handling in there somewhere :laugh:

They sound like the stock ones. From memory stock front is 30mm and rear is 24mm BUT they are hollow. So taping them nay give you the indication.

The GB ones are 32mm front and 27mm rear and both are solid so it is something like 70% stiffer than the factory ones.

Stock bars are; front, hollow;30mm. Rear, hollow; 18mm

Whiteline Group Buy are Front, solid 32mm Blade adjustable. Rear, solid; 20mm Blade adjustable.

Thanks. Will give tapping a try tomorrow.

Did more searching with some success for a change and found posts from 2008 where Sydneykid wrote yours was 18mm rear hollow and he replaced it with 24mm solid?

Anyone else checked what is on their ARX?

Correct. I used the same dimensions as the original Sydneykid bars (as fitted to Andy's, and others) 30mm solid front, & 24mm solid rear for my first Group Buy through Signature.

I have no reason to believe the AR-X has different OEM bars to any other NM35, and the part numbers back this up.

Thanks - Seem to have established my rear bar at 24mm is not stock. The front one has exactly the same finish so it might not be as well. Will have a better look for some sort of labelling.

Thanks. Will give tapping a try tomorrow.

Did more searching with some success for a change and found posts from 2008 where Sydneykid wrote yours was 18mm rear hollow and he replaced it with 24mm solid?

Anyone else checked what is on their ARX?

Looks like the memory is starting to fail me.... lol

Just a thought... If anyone would post a DIY step-by-step on how to install the Whiteline goodies with as many photos as possible for us noobs, would be real nice of you "gurus"... ;)

Most things like this sort of DIY already exist on the forum.. You just need to search..

Most things like this sort of DIY already exist on the forum.. You just need to search..

I will do some research but with the V35 is the sway bar going to be as noticeable as you guys in the Stageas? I already have BC Racing BR coilovers and a front Strut bar on the way (wonder if i should send it back and get sway bar instead) ? Any thoughts? I take my car mountain runs often and will be going to track

I will do some research but with the V35 is the sway bar going to be as noticeable as you guys in the Stageas? I already have BC Racing BR coilovers and a front Strut bar on the way (wonder if i should send it back and get sway bar instead) ? Any thoughts? I take my car mountain runs often and will be going to track

For dollars spent, I believe Sway Bars to be the most beneficial suspension modification you can make to any car.

I'm also running a set of BC's and they made a huge difference, but the Sway Bars are just the icing on the cake.:thumbsup: I'd hang on to the strut brace if I was you.

The V35 should be compatible with the 350Z bars Whiteline already make. If there is demand from the V series guys, I'll run a separate group buy, but so far there hasn't been an overwhelming response to the offer I've already made.

Cheers, Dale.

For dollars spent, I believe Sway Bars to be the most beneficial suspension modification you can make to any car.

I'm also running a set of BC's and they made a huge difference, but the Sway Bars are just the icing on the cake.:thumbsup: I'd hang on to the strut brace if I was you.

The V35 should be compatible with the 350Z bars Whiteline already make. If there is demand from the V series guys, I'll run a separate group buy, but so far there hasn't been an overwhelming response to the offer I've already made.

Cheers, Dale.

You have listed quite a few different parts, which ones do you need for front and back and do you need both?

You think its worth keeping the front strut bar and finally can you just add a V35 sway bar to your order :)

Ok guys, we're in the final week of the Group Buy and there are still four spots left :whistling:

There was huge interest in the lead up to this Group Buy and people had been nagging me for months. I'd really like to get it up to the 10.

Anyone who wishes to get on board; I welcome your participation, this is how we demonstrate to Whiteline that our vehicle is worth supporting. There's no point whining about the lask of aftermarket support, then waiting for everyone else to buy in first. We have a proven product; from an Australian company, what more can you ask for?

Be a pioneer; have something all the other Stagea drivers wish they had.

To be honest; if we don't fill this group buy, I'm very sad to say, I don't believe I'll be going to the effort of organising another one.

Thanks again to the guys who got on board and supported this venture, I really appreciate it. You've been a dream to deal with.

Cheers, Dale.

I guess that's the hard thing about organising a GB...you get all these people saying "yeah I want it" but when its time to pony up hardly anyone responds...

I'm looking at doing a Goodridge braided brake lines GB pending results from KV1...but think I can't be bothered dealing with the drama...

Also sucks that it makes you look lame in front of Whiteline as you've done a great deal in pushing them to get a product made for our car and now we can't even get 10 people to buy it! :unsure:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...