Jump to content
SAU Community

Whiteline Nm35 Stagea Sway Bar Group Buy

Daleo

By Daleo,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Daleo Grand Master

Daleo

Posted
  • Author
Posted

Got these fitted today, look great, thanks Dale!

Rear bar was an issue, not a lot of clearance around my exhaust, but it *just* fit! :cheers:

Front one was a bit of a bitch with the links and mounting points, but not too bad. No issues with rubbing/grinding.

Are there adjustable links available for the front?

So far I don't feel much of a difference, but going for a hills run tomorrow to see how it is on a windy road. I have a feeling my stuffed stock shocks won't be helping the situation, so have to bump coilovers up the list...

I didn't end up getting the adjustable rear toe arms installed. Dad and I did the install in his workshop and he recommended I get them to fit it when I next get a wheel alignment. I think I'll do that in the next week or two, as we did notice some feathering on the rear tyres that we didn't notice at the service around 1000-2000 km ago.

That's great mate! It is a little tricky to thread in around the exhaust, but it's possible. Dropping a couple of the hangers helps with getting a bit more space.

I have some very short Whiteline H/D Ball Links that I've been working with, on and off for a while now; It's proving quite difficult, as due to the angle up over the top of the lower control arm, it's difficult to get the same kind of articulation available with the OEM links.

The OEM ones don't suffer for strength, so I'm not looking to pursue it much further. The amount of machined parts I've had to manufacture so far (spacers, shouldered bushes and mount plates) to adapt the universal links would make them fairly pricey, for something that doesn't really work as well as the original.

  • Replies 282
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

scotty nm35
scotty nm35

Daleo's bracing, and the Superpro compression bushes give a much more pronounced handling improvement than the sways imo. Not saying 'don't get em' but increasing the spring rate isn't going to improv

Daleo
Daleo

I am organising another group buy for NM 35 Stagea Sway Bars. We require a MINIMUM of 5 orders to go ahead. Whiteline; http://www.whiteline.com.au/index.php have just added these exciting new product

DrMoShen
DrMoShen

I'd like to get some bits if they are compatible. Does anyone know if these will fit a 2007 rear wheel drive PM35? >I can PM the VIN if required.

Posted Images

bigkevracer Grand Master

bigkevracer

Posted
Posted

No problems Dale, thanks.

I did actually drop a couple of hangers while we were doing the fitting. Not sure if its such an issue on cars with different exhausts, but it did just fit, so no issues.

Took it for a hills run today and what a difference! Body roll is greatly reduced and turn in is much improved. Love it! Even the girlfriend noticed the difference!

Thanks for your efforts Dale, much appreciated.

  • 1 month later...
prince_skyline Community Regular

prince_skyline

Posted
Posted

Well i finally had time to fit the Sway bars today......no problems encountered with the install at all. Took advice from here and dropped the exhaust from the back two hangers to allow more room for the rear bar to be removed and new one installed.

First impression was how solid and firm it made the steering feel from the wheel, even simple turns and lane changes....

Certainly notice that there is less body roll and it is noticeably more 'eager' to duck into turns. Cornering feels much more natural. I dont feel like I am fighting the car around the corner anymore but more guiding it through - feels like the car is now inviting me to take each corner faster! :whistling:

Well worth the investment :cheers:

Thanks again Dale :thumbsup:

Daleo Grand Master

Daleo

Posted
  • Author
Posted

Well i finally had time to fit the Sway bars today......no problems encountered with the install at all. Took advice from here and dropped the exhaust from the back two hangers to allow more room for the rear bar to be removed and new one installed.

First impression was how solid and firm it made the steering feel from the wheel, even simple turns and lane changes....

Certainly notice that there is less body roll and it is noticeably more 'eager' to duck into turns. Cornering feels much more natural. I dont feel like I am fighting the car around the corner anymore but more guiding it through - feels like the car is now inviting me to take each corner faster! :whistling:

Well worth the investment :cheers:

Thanks again Dale :thumbsup:

Great to hear mate, glad you got them on with no issues :thumbsup: .

I reckon they make the car feel so much smaller and nimble to drive.

Thanks for the positive feedback; both about the bars and for myself, really appreciated.:cheers:

Off topic; You don't happen to know a guy called Shaun Chillcot? I work with him, he's a Prince nut; reckons he's seen a couple of your cars...

Cheers, Dale.

prince_skyline Community Regular

prince_skyline

Posted
Posted (edited)

Certainly do know Shaun. He recently sold one of his cars. He would know me also seeing he should be getting all my emails from The Prince Skyline GT Register. First met him at Bathurst in 2006 when i organised a National Meeting for the Prince Register. I had my light blue Prince there. Had a good long chat with Shaun at the bar on the first night. Beers were flowin' nicely...

Say g'day for me....

Edited by prince_skyline
Daleo Grand Master

Daleo

Posted
  • Author
Posted

Certainly do know Shaun. He recently sold one of his cars. He would know me also seeing he should be getting all my emails from The Prince Skyline GT Register. First met him at Bathurst in 2006 when i organised a National Meeting for the Prince Register. I had my light blue Prince there. Had a good long chat with Shaun at the bar on the first night. Beers were flowin' nicely...

Say g'day for me....

Will do mate, yeah I don't think he really wanted to let it go, but I think he got what he was wanting; pricewise.

Shaun likes a drink & a chat? Lol, I had no idea...:whistling:

  • 4 months later...
  • 1 year later...
Daleo Grand Master

Daleo

Posted
  • Author
Posted

Hi guys,
I'm rather sad to inform you all; but Whiteline's BNF44Z and BNR38Z will now no longer be available. :/

Over the last 12 months demand for these has steadily declined, to the point that Whiteline are not planning another production run unless they receive an order for 25-30 complete sets.
I cannot possibly afford to make an order that large; and current demand suggests that it would take me years to sell them if I did.

I'm not that surprised, as our vehicle is a very small market, and we are essentially the only place in the world that has a decent number outside Japan.
Most other Whiteline products have large markets; often in multiple countries, so it is understandable that it is not cost effective to keep large numbers of low demand parts in stock costing large amounts of store.
I'd prefer people didn't criticize Whiteline for dropping these parts from their line-up; if we had reasonable demand they would still be producing.
If you are ready to grizzle; ask yourself if you supported them & bought a set. :whistling:

Note that this doesn't affect the availability of any other parts; on the BNF44Z and BNR38Z. Whiteline continue to supply all other parts and replacement bushes.

I'd like to take this opportunity to thank Whiteline for supporting us with both excellent quality parts and back up, and for continuing to bring innovative, high quality handling & alignment parts to the market.

When I found out what was happening; I had my supplier grab any complete sets that were available. I managed to get what I believe are the last 2 pairs available. I have one pair left.

Cheers, Dale.

Daleo Grand Master

Daleo

Posted
  • Author
Posted

It is, but there are plenty of "wait & see" buyers that will be ready to complain now they can't get them.

Pretty much, the market is pretty well supplied now; I'd need a decent order to justify past what material I have left.

Never say never though.

Commsman Veteran

Commsman

Posted
Posted

It is, but there are plenty of "wait & see" buyers that will be ready to complain now they can't get them.

Pretty much, the market is pretty well supplied now; I'd need a decent order to justify past what material I have left.

Never say never though.

If this last bit ^ is referring the front chassis brace, I was joking seeeing as you make them, not (some sweat shop working for) Whiteline, lol.

I hope mine is made before you run out of material or I'll be sad :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...