Jump to content
SAU Community

Recommended Posts

my first problem with the car, its intermitantly idleing really high, like 1500rpm in "drive" and 2500 in nuetral.

noticed i had wired the thermo fan up backwards but the car didnt overheat.

as far as i can tell by the boost gauge its still on the correct vacuum at normal idle.

any idea's i need to get this sorted before the starlight charrity cruise on sunday!!!! :(

Funny, I'm not convinced my thermo fan is turning on, but I'm still running about the same water temps as everyone else, ~90deg according to the informeter.

That probably doesn't tell you much, but what vacuum are you showing at idle? What gauge do you have?

Funny, I'm not convinced my thermo fan is turning on, but I'm still running about the same water temps as everyone else, ~90deg according to the informeter.

That probably doesn't tell you much, but what vacuum are you showing at idle? What gauge do you have?

ive got a Autometre sport comp II - idle nuetral and in drive is 15/16 In.Hg

pulled the intake apart there's no signs of oil around the throttle body so its not that.

took the car for a drive to warm it up didnt have any hastles but when i got back i noticed in nuetral its normal at 15In.Hg but in gear its sitting at 19In.Hg

tryed playing with some of the vacuum hoses when i pulled out the one before the solinoid/valve for the fuel breather i think it is, it drops back to around 15/16In.hg so i wonder if thats the problem..............

other than that i cant tell much else.................. any one else had these problems???

Brake booster? Fuel reg or dampener?

The only one I have heard leaking, on almost every M35 I have worked on is the PCV hose, it goes hard and leaks around the fitting on the plenum end. The fuel reg hoses sometimes pop off too.

Heated seats are damn good in winter. But on several occasions I've bumped the switch without realising it and my balls gets toasted..

haha yeah i hated accidently doing that especially in qld.. youd wonder why your legs and back would start sweating until you saw the orange light.

what i found was more disturbing was when you attempted to reverse in snow mode instead of sports mode and it would do that jerk motion like trying to rock itself out of a boggy ditch , and never fully engage the diff

without realising you had flicked the switch. ;)

i only 'had' a rx , everyone seems to have much better ones on the forum if i was going to buy again it would be axis then RS depending on looks/condition . all i had was the heated seats. no lsd , but fortunately no hicas!

(wonders if he'll get shamed out for choosing a c34 instead next time a late model neo based one or a 260rs - theyre getting cheaper!)

Edited by PetroDola
  • 2 weeks later...

already put 10,000Km on her since i bought it gave her my first oil change, went with the royal purple seeing as it was on special and drilled out the turbo oil restrictor bango bolt.

its been an awesome car so far, dont regret for one second buy it. (fuel bills are a bit high but hay its worth it) and on a top note havent had any drama's with her other than my own silly mistake with the boost gauge line getting caught up in the accelerator pedal LOL so touch wood it'll be happy motoring for a long time yet :D

im thankful for all the great info on this site and all the people who take the time to help out, its muchly appreciated.

no real plans for the car in the near future just goin to enjoy it and drive her untill the 2nd quarter of next year then i'll do a few more mods like strut braces and start saving for the turbo mods hopefully it doesnt rear its ugly head to soon!!!

You wont be able to fit a strut brace with the spacer on. Ive got a strut brace and there is just no room for a spacer.

Im tempted to remove it now that Ive got the BCs in, see what difference it makes, but when I first fitted it I felt it straight away. Much more direct and tighter.

i think my BOV is starting to cause more problems than just farting so im looking for an easy aftermarket replacement................. what have you used and what would you recommened.

here's one i found i'll have to find out if its suitable.............. Turbosmart Kompact

any help appreciated :)

I'm using the model up, the Nissan Specific Dual Port: http://www.ebay.com.au/itm/Turbosmart-Dual-Port-Blow-Off-Valve-Skyline-R32-R34-/130553048394?pt=Motors_Car_Truck_Parts_Accessories&hash=item1e65916d4a

Just got it Thursday, put it in, and drove with it around the place over the weekend, about 200k on it. A lot more flutter than I was expecting, even after playing with the adjustment all weekend.

I installed it as a plumb back, and it works fine with the stock map. It idles and runs fine no matter what I do to the adjustment.

Reason I went with this one was because Turbosmart told me the Kompact was no good for about 15-16PSI+. Figured I'd give the dual port a crack.

I bought it from those ebay guys above, quick turnaround, everything was good. But when I bought it, the listing was for $US299 with free shipping.

Reason I went with this one was because Turbosmart told me the Kompact was no good for about 15-16PSI+. Figured I'd give the dual port a crack.

Obviously false info, its running fine at 30psi, as long as its plumbed back... :)

Kompact is plumb back only anyway isn't it?

I suspect after talking to Aaron that the person I spoke to didn't know about the stiffer spring. Happy with what I have though, and when I bought it the exchange rate was quite favourable so price was ok.

Although I'm still not sure if the flutter is cool or annoying...

Kompact is plumb back only anyway isn't it?

I suspect after talking to Aaron that the person I spoke to didn't know about the stiffer spring. Happy with what I have though, and when I bought it the exchange rate was quite favourable so price was ok.

Although I'm still not sure if the flutter is cool or annoying...

any chance you can get a "sound clip" of it ???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...