Jump to content
SAU Community

Recommended Posts

Hi All,

I've been trying to find safe/normal operating temperatures for an RB25det, a good idle seems to be about 80c, but what is considered a safe temperature when you start pushing or tracking the car?

After just fitting a replacement engine to my 33 I've been watching the temps very carefully, my dash gauge never moves above 1/4 no matter how hot shit gets so I've been using a consult cable to read from the ecu, currently running water through the system as the engine has only been in for a couple of days and I'm checking for leaks etc. City driving sees 80-86c, I was at wot in 3rd for 15-20 secs heading up a steep hill right after a spirited drive and temps reached 98c, obviously water becomes fairly useless at this point so I just coasted down allowing it to cool.

Is +100c normal for an RB being driven hard? If so I guess I should switch to some coolant asap.

Link to comment
https://www.sau.com.au/forums/topic/359460-rb25-operating-temperatures/
Share on other sites

You talking stock radiator? I wouldn't be tracking with a stock one. I mean you can in a stockish car, but its not really ideal.

With a aftermarket radiator, my RB25 and RB26 both sit between 67-75 putting around. Only giving it an absolute gut full will see upwards of 80+

IMO invest in a radiator if you are see 98, thats up there.

  • Sad 1

Hi All,

I've been trying to find safe/normal operating temperatures for an RB25det, a good idle seems to be about 80c, but what is considered a safe temperature when you start pushing or tracking the car?

After just fitting a replacement engine to my 33 I've been watching the temps very carefully, my dash gauge never moves above 1/4 no matter how hot shit gets so I've been using a consult cable to read from the ecu, currently running water through the system as the engine has only been in for a couple of days and I'm checking for leaks etc. City driving sees 80-86c, I was at wot in 3rd for 15-20 secs heading up a steep hill right after a spirited drive and temps reached 98c, obviously water becomes fairly useless at this point so I just coasted down allowing it to cool.

Is +100c normal for an RB being driven hard? If so I guess I should switch to some coolant asap.

I have an R34 - usually runs 85-89c - on hot days it runs 90-103c depending on load.

Hard driving on a moderate day is low 90s

I'm running Castrol 33% coolant.

My car is stock.

Edited by iseekool

Normal street driving on belter hot days, the highest I've seen in either car was 95deg, nothing to worry about.

The 32, on a 40+ day and a good 2 min skid, the highest I've seen is 105deg which was fkn hot but still didn't throw any coolant.

Coolant, under pressure, isn't going to boil until about 110deg. If you're seeing about 100deg or higher on the street or highway, then you've got issues that need addressed.

From my experience, RB's like to operate at about 80deg (RB20/25non-neo/26), they run a 76.5deg thermostat. The neos seem to want to run a bit hotter (probably due to emissions reasons) and they run an 82deg thermostat.

Edit: I also had way better results from a stock GTR radiator than the 50mm chinese alloy thing I used to have.

Edited by bubba

I have an R34 - usually runs 85-89c - on hot days it runs 90-103c depending on load.

Hard driving on a moderate day is low 90s

I'm running Castrol 33% coolant.

My car is stock.

It's worth noting that R34 have a much higher thermostat than the R33 (off the topic of my head I beleive it starts opening around 80-82C and fully open by 95C?). I believe these hotter running temperatures were done as part of the LEV modifications (ie: lower emissions) ..

My R34 sees similar temperature ranges as above on a stock radiator (using tectalloy 100 coolant), fresh thermostat, recently changed fluid, etc. Planning to put a bigger radiator in within the next few weeks. I will note I saw much higher temperatures (105+ on hot days stopped in traffic) when I had a nismo radiator cap fitted - not sure why that is.

Coolant doesn't make your engine run cooler, all it does is increase the boiling point. In fact, due to Ethylene Glycol being an oil product, it actually reduces the thermal efficiency of water. Only products that reduce surface tension are going to reduce temps

  • Like 1

I boiled all the water/coolant at my last track day. Would have been 120degrees PLUS.

Hopefully my dedicated RB26 r32 sedan track car never sees boiling point, not a nice feeling wondering if youve ruined your engine.

If I didnt have a thick headgasket on my RB25 (stock bottom end, ported head, gt3076) Im sure it would have shagged the engine......

It could be your stock radiator is blocked with sludge. best to replace it with a thicker dual/triple core aluminium 'race' item. The one in my

RB26 is from ASI in melbourne @52mm thick, the RB25 radiator is a Koyo 40mm thick item

Thanks for the replies guys.

I have an R34 - usually runs 85-89c - on hot days it runs 90-103c depending on load.

The NEO does run a bit warmer than the earlier 25's, my thoughs were inline with R31Nismoid and bubba, for a '96 RB25 I was expecting to see 80-90c but had never monitored it after a hard drive to know for sure.

Current radiator has had various mixtures of chemiweld and oil through it in a previous life, even though it's been flushed it's probably rooted. I guess I'll be looking at an aftermarket radiator for peace of mind :thumbsup:

nissan thermostat for all RBs except 34s is 76.5C, but the thermostat is in the bottom hose (coolest point), temp sender is in the top hose, which is the hottest point of the system.

i see the same temps as nismoid, high 60s to low 70s, but thats not normal, seams to be a 31 thing.

I always thought it just to be a 31 thing with added space in engine bay and around the front of the car aiding airflow.

My GTR does as well though with a decent after market rad, which I found interesting and dispelled that one.

  • Sad 1

Mine sits at ~82 during a normal day without A/C & will go up a couple of degrees when stuck in traffic.

In a 38C+ day with A/C on, it will go over 90C when stuck in traffic but will drop back down to about 85 when moving at decent speed again.

This is with a stock radiator, recently got the plastic top tank repaired & rad cap and thermostat replaced.

  • 3 months later...
  • 7 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...