Jump to content
SAU Community

Recommended Posts

26psi and 460rwkw on e85 twin nismo intanks no pump noise at all.. Very little change in spool from 98 octane + 30% tolulene to e85. sad.gif

any info on the install for the twin Nismos, i put twin nismos in my car last week.

are yours wired to the battery? or are they just wired into the factory wiring?

how did u mount them in the tank?

cheers

Iv installed them into a 33GTR so much easier than 32.

Posted a picture on GTRUK:

http://www.gtr.co.uk/forum/119259-rips-fuel-system.html

I used feed and return outlets on the plastic tank cap as twin feeds and added a speedflow bulk head fitting to the cap for the return line. Inside tank wiring i used the factory internal wiring for 1 pump but for the 2nd pump i added 2 posts to the cap with some 6mm stainless rod and nutted both sides. Feeding the pumps i used 2 relays feed directly from the battery. ;)

what did u mount the pumps to inside the tank? i did basicly the same thing with the big hose clamp, i clamped my pumps ethier side of the cradle. so my pick ups arnt inside the baffle thing in the bottom of the tank, but the picks are ether side of it, at the lowest point.

im in the middle of relocating my battery, once its in the boot ill run a similair setup to you with wiring..... ive just got a Y section atm in the tank joining the 2 pumps into 1 factory line, as im only running a factory rail atm.... but ive got a sard rail here and im considering running twin lines and puting one on each side of the rail... but see how i go.

Cant move much down there its simliar to a surge tank i guess. Yep twin entry rail setup using the standard steel lines as my feeds and i ran one -6 braided the length of the car. So much nicer setup than the twin 044's surge tank crap i had in there at first.

usng the existing steel lines as your feed to the twin entry rail is what i did - nice & clean setup.

just run a return line under the car & its done.

dean - how much power are u supporting? if you look at the likes of GTRNUR & others on this site, there are guys cracking over 400awkw with the factory single entry rail. however, i also ran a twin entry rail on 405awkw for bling :)

ATM I'm only making 330rwkw, but Im making a 4inch exhuast and installing some id2ks going for around 400, it doesn't matter ATM anyway as a built motor will be going into this car shortly so I more as well set the fuel system up.

How did you mount your twin pumps in the tank???

i actually ran an in-boot surge tank with an 044 lift pump (because it is already in there, not required though) & 2 044s mounted on the surge tank.

my fuel used to get hot though & i always had fuel fumes in the cabin.

i wasnt happy with the fuel setup but it did its job

I was Gunna take a pic of my setup, just to c what people think, but I'm to scared to stick a camera in the fuel tank and take a photo or put my phone near it to take it. Way to much fumes around, and the flash will most likly blow up my shed...... So Fark that

I was Gunna take a pic of my setup, just to c what people think, but I'm to scared to stick a camera in the fuel tank and take a photo or put my phone near it to take it. Way to much fumes around, and the flash will most likly blow up my shed...... So Fark that

Haha that is an awesome post :)

We should write to mythbusters to see if this is the case :)

Yea lol not to keen on trying it myself.

It's hard with the r32 tank, as there's no way you can fit both pumps into the cradle in the bottom of the tank. So I spose the way I've got it, is really the only way you can do it, unless you mount the pumps to lid and hang the pick ups down.....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, I started this repair and got as far as "fixing" the holes with some fibreglass. God all those years working on boats came back quickly. I decided I'd reach out to some rust guys just to see what they would say about it. I came across a guy about 40 mins away and went to see him. He said the windscreen needs to come out, that there might be some more bits around the windscreen and he'd quote them at the time. But his quote was $300 to remove and replace windscreen and $3k for the damage he can see. He said he could respray the roof for $1200 and the bonnet for another $800 (somebody has previously rattle canned it, its horrendous). This is $5300 + any small additional bits. It's a lot, I get that and the name of one of my fave youtube channels 'Not Economically Viable' comes to mind.  I'm not being financially rational, but I've taken him up on the quote. He's opening a new shop in November with more room, so we're waiting for that. I'll leave the currently missing headliner out until then. I'm looking forward to it being fixed and having the paint looking nice again (lots of clear coat issues on the roof too). / flame suit on.
    • Oh and some up-and-comings; New rear drivers wheel bearing. I'll do that this weekend while the diff is out. The car is already up and the d/c axles and missing exhaust will help with space. This is the last bearing for me to do and I've been dragging my feet on it. I also have some new EBC blue stuff pads for the car and some new brake fluid. I haven't ever flushed the fluid in this car and looking forward to it. I have 600 degree fluid to put in. Not exactly "race fluid" but better than the typical stuff I have been using.
    • A proper clutch/plate type mechanical diff with quite a lot of pre-load and high locking % is better for drifting. Much more consistent in its behaviour. A helical can be annoyingly vague and inconsistent in how it responds under the sorts of abuse found in drifting.
    • Some updates here. I pulled the entire interior out, minus some trim to respray the seats with Colourlock dye. It turned out really nice though I accidentally let the dog in the car after and she scratched up the front seat.  This is what it looked like before, the colour was just washing out everywhere but thankfully the leather was in good nic. Then after the respray   And after the bloody dog jumped in The headliner is out waiting to be retrimmed, but it will stay out now until Nov - see why below. I replaced the stereo/headunit with a period-styled Android headunit. I have no after pics, but I'll get some. This is because of the missing pixels. I tried to fix this twice with replacement ribbon cables but couldn't. Also the bluetooth interface I'd bought for this was crap. Then there's the rusty roof. Pics and info in this other thread. I have decided to get this repaired professionally, but I'll update that thread. This is why the headliner will stay out for now. I'll be getting the roof and bonnet resprayed at the same time the rust is fixed. I also had an interesting issue with my drivers door lock.  For a small period I was having issues getting any 12v power to the car - I mean *any*. It would have no dash lights, nothing. It happened while I was at the shops and I couldn't get in the car. So, we had 2 problems. The most pressing here is that I was locked out. I have only a single physical key hole on the car, the drivers door and no amount of turning would unlock the car. Surely it doesn't need power for this? The second issue is why am I losing all power periodically, The battery isn't dead, its almost like the battery isn't even there. Two issues that were surprisingly easy to fix. You fellow BMW over-engineering lovers will appreciate this. The lock in the door has 5 states; mechanical lock, electric lock, neutral, electric unlock, mechanical unlock achieved at -90 degrees, -45 degrees, 0 degrees, 45 degrees and 90 degrees. Although, the unlock is towards the front of the car, so opposite for LHD countries. Sticking the key in and turning 45 left or right is what is used 99% of the time. It activates the central locking etc. 90 degrees is for dead battery access and, obvs, only un/locks the one door. But because the mechanical lock is never used and is 27 years old, it seizes up. I was totally unable to turn the key far enough to get to the mechanical unlock (At the time of locking myself out, I didn't even know this was a thing). I eventually did it with some vicegrips and teflon spray.  I made a quick vid for other E39 peeps.   The battery issue is totally new to me also - It wasn't making sufficient contact between the post and the terminal. The terminal was bolted on tight, but the car wouldn't have power. After checking the battery with my multimeter I accidentally contacted the terminal and the battery post and the car got power. The battery was only a few years old and in good condition. I cleaned the post and the terminal with a wire brush, bolted it back on tight and never had the issue again. I'm still surprised that despite having solid contact it didn't work. Also, the car was getting Warragamba sized pools of water in the back when it rained. My initial concern was another rust problem. But when I went out on Weds while it was raining and while I had no headliner in I could see a steady stream of water coming through the roof mounted aerial. As this aerial is for the (now removed) car phone I pulled it out and whacked a blanking grommet in the hole. It seems fine now. I'm thinking I might get the hole permanently filled when the rust is fixed. Moving forward and things in progress; The tailgate needs some attention. I have taken all the trim off to clean it all and address some small rust spots. I have partially done all of this but I'll finish it up hopefully this weekend. As all the trim are now entirely devoid of trim clips I have bought a heap of strong velcro and I'm hoping it does a good enough job as any of this trim in good condition is super expensive and usually in Europe as we dont have many of the wagons here. Suspension and brakes!!! This is exciting. In the front; New control arms New sway bar links New lower Eibach springs (the only modification I'm planning on this car) M Sport shocks (these came with the car and will replace the longer shocks in the car) New top mounts Used 540i calipers (stock brakes suck!) New 540i disks and pads (22x296 mm for 528 and 30x334 mm for 540i) New front wheel bearings (thank all that is holy for bolt on bearings!) Annnnd in the back; New control arms New sway bar links Adjustable air suspension arms (fool the car into what the current height is so the self levelling suspension can match the new front ride height) New ball joints I'll also be doing a brake fluid flush while I'm in there. I'm planning on switching the car over to the 16's that came with it so I can clean up and respray the M Sport 17's. They've lost a lot of colour over the years and have some gutter rash. None of this will start until the E90 is back.
    • You mean you will regret it for drifting duties? I don't quite follow.
×
×
  • Create New...