Jump to content
SAU Community

Recommended Posts

26psi and 460rwkw on e85 twin nismo intanks no pump noise at all.. Very little change in spool from 98 octane + 30% tolulene to e85. sad.gif

any info on the install for the twin Nismos, i put twin nismos in my car last week.

are yours wired to the battery? or are they just wired into the factory wiring?

how did u mount them in the tank?

cheers

Iv installed them into a 33GTR so much easier than 32.

Posted a picture on GTRUK:

http://www.gtr.co.uk/forum/119259-rips-fuel-system.html

I used feed and return outlets on the plastic tank cap as twin feeds and added a speedflow bulk head fitting to the cap for the return line. Inside tank wiring i used the factory internal wiring for 1 pump but for the 2nd pump i added 2 posts to the cap with some 6mm stainless rod and nutted both sides. Feeding the pumps i used 2 relays feed directly from the battery. ;)

what did u mount the pumps to inside the tank? i did basicly the same thing with the big hose clamp, i clamped my pumps ethier side of the cradle. so my pick ups arnt inside the baffle thing in the bottom of the tank, but the picks are ether side of it, at the lowest point.

im in the middle of relocating my battery, once its in the boot ill run a similair setup to you with wiring..... ive just got a Y section atm in the tank joining the 2 pumps into 1 factory line, as im only running a factory rail atm.... but ive got a sard rail here and im considering running twin lines and puting one on each side of the rail... but see how i go.

Cant move much down there its simliar to a surge tank i guess. Yep twin entry rail setup using the standard steel lines as my feeds and i ran one -6 braided the length of the car. So much nicer setup than the twin 044's surge tank crap i had in there at first.

usng the existing steel lines as your feed to the twin entry rail is what i did - nice & clean setup.

just run a return line under the car & its done.

dean - how much power are u supporting? if you look at the likes of GTRNUR & others on this site, there are guys cracking over 400awkw with the factory single entry rail. however, i also ran a twin entry rail on 405awkw for bling :)

ATM I'm only making 330rwkw, but Im making a 4inch exhuast and installing some id2ks going for around 400, it doesn't matter ATM anyway as a built motor will be going into this car shortly so I more as well set the fuel system up.

How did you mount your twin pumps in the tank???

i actually ran an in-boot surge tank with an 044 lift pump (because it is already in there, not required though) & 2 044s mounted on the surge tank.

my fuel used to get hot though & i always had fuel fumes in the cabin.

i wasnt happy with the fuel setup but it did its job

I was Gunna take a pic of my setup, just to c what people think, but I'm to scared to stick a camera in the fuel tank and take a photo or put my phone near it to take it. Way to much fumes around, and the flash will most likly blow up my shed...... So Fark that

I was Gunna take a pic of my setup, just to c what people think, but I'm to scared to stick a camera in the fuel tank and take a photo or put my phone near it to take it. Way to much fumes around, and the flash will most likly blow up my shed...... So Fark that

Haha that is an awesome post :)

We should write to mythbusters to see if this is the case :)

Yea lol not to keen on trying it myself.

It's hard with the r32 tank, as there's no way you can fit both pumps into the cradle in the bottom of the tank. So I spose the way I've got it, is really the only way you can do it, unless you mount the pumps to lid and hang the pick ups down.....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...