Jump to content
SAU Community

Recommended Posts

Im after a taller diff ratio. Something around the 3.5 ratio or even taller. I have a 3.7 gears here but want to see if I can get something taller before I have it built.

I have heard R33 RB25de auto has a 3.5 diff. Would take the complete centre if someone has one laying around.

  • 2 weeks later...

Gday, I'm after an R32 GTS-t Manual tail shaft in good condition if anyone can help out, must not have shagged centre bearing/carrier bracket thing like they all appear to - Gearbox Yoke not required either.

Also after some good condition genuine R32 GTR front Guards

Send me a message if you can help - Tobbie - 0401 739 292 Thanks!

  • 2 weeks later...
  • 3 weeks later...

WTB urgently, the steel water pipes that bolt to the underside of an RB25 inlet manifold, will pay in parts, cash or alcohol!

Will also buy a whole plenum if its cheap/easier.

SMS on 0408 117 171

could try zoidbergmerc he offered me a plenum a couple of weeks ago,

WTB urgently, the steel water pipes that bolt to the underside of an RB25 inlet manifold, will pay in parts, cash or alcohol!

Will also buy a whole plenum if its cheap/easier.

SMS on 0408 117 171

ah oh well

yeah not bad, took it to rons and he managed to take out the old piece and got midas to make up a new piece, now no leaks :D

so its all good, heaps easier than having to replace the whole thing!

now im just waiting for my thermostat to arrive and then im doing oil, fuel filters before powercruise...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...