Jump to content
SAU Community

Recommended Posts

  On 10/05/2011 at 4:36 AM, DVS32R said:

I ran a t04Z with stock afms so u will be fine

Did you get any problems with the Afm's voltage spiking to much under light on/off throttle causing the car to stutter or hesitate and sometimes cause it to stall?

Link to comment
https://www.sau.com.au/forums/topic/363731-rb26-to4z-setup/#findComment-5804218
Share on other sites

  On 10/05/2011 at 4:37 AM, SimonR32 said:

I much prefer the D-jetro option, speak to your tuner though they should have a preference...

Cheers matey im seriously considering going this route and being done with it but my tuner has said that the car will be alot smoother and nicer to drive with normal power fc and afm's as opposed to d-jetro and a map sensor.. How do you find the d-jetro when your holding a certain speed on freeway and when your on off the throttle in traffic etc?

Link to comment
https://www.sau.com.au/forums/topic/363731-rb26-to4z-setup/#findComment-5804279
Share on other sites

  On 10/05/2011 at 5:17 AM, jun 2.7 said:

Cheers matey im seriously considering going this route and being done with it but my tuner has said that the car will be alot smoother and nicer to drive with normal power fc and afm's as opposed to d-jetro and a map sensor.. How do you find the d-jetro when your holding a certain speed on freeway and when your on off the throttle in traffic etc?

That sounds like your tuner doesnt know how to tune d-jetro properly, so if you stay with that tuner, use afms.

Link to comment
https://www.sau.com.au/forums/topic/363731-rb26-to4z-setup/#findComment-5804324
Share on other sites

  On 10/05/2011 at 4:56 AM, jun 2.7 said:

Did you get any problems with the Afm's voltage spiking to much under light on/off throttle causing the car to stutter or hesitate and sometimes cause it to stall?

this only occurs if the AFM are too close to the inlet, and reverberation etc.

if its spaced as far as possible, these issues seem not to occur

Link to comment
https://www.sau.com.au/forums/topic/363731-rb26-to4z-setup/#findComment-5804406
Share on other sites

  On 10/05/2011 at 6:30 AM, mico said:

any tuner with experience will tell u the d jetro is a drag computer only. costs less to tune an apexi with afm's, and is smoother on the street.

Maybe they will tell you that... on planet retard :wacko:

Link to comment
https://www.sau.com.au/forums/topic/363731-rb26-to4z-setup/#findComment-5804441
Share on other sites

agree, djetro and ljetro (ref DVS32R)

both are the same to tune and setup, and i think from memory the djetro takes longer as you have to work so much harder at the transient throttle process more to get it nice, vs AFM that is bulletproof on the factory maps on the powerfc, ie you dont have to focus so much on that area (from no throttle, to light throttle)

both will make same power and response

but will perform differently as far as mapping and scaling are concerned

but back on topic,

you should not max twin Z32s with T04Z

Link to comment
https://www.sau.com.au/forums/topic/363731-rb26-to4z-setup/#findComment-5804875
Share on other sites

  On 10/05/2011 at 12:41 PM, Ryan1200 said:

This is the log from my 460awkw dyno run. 26psi 2530's

The Z32's have some voltage left but the 800cc injectors are out...

Jebuz! Is that on 98? Do the HKS turbos make more power than the -5s? I thought 400awkw was the limit of 2530/-5s on pump.

Link to comment
https://www.sau.com.au/forums/topic/363731-rb26-to4z-setup/#findComment-5805708
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...