Jump to content
SAU Community

Recommended Posts

hey guys rebuilding my bottem end after oil pump failure i already have a custom oil drain from back of head back down to sump

my question is do i really need higher volume sump if im making about 500 bhp i currently have stock sump .... and also should i change harmonic balencer and put after market one if so

what brand /model no. ??

Link to comment
https://www.sau.com.au/forums/topic/365969-gtr-89-32-build/
Share on other sites

If going with a higher flowing pump then yes you need a bigger capacity sump, head restrictors etc (replacing with a R33 crank for the long oil drive would be recommended). read the oil control thread in it's entirety.. as for head oil drains, as far as their function.. the general consensus is they don't really work.

I wouldn't risk using that balancer again if there were a oil pump failure.

Link to comment
https://www.sau.com.au/forums/topic/365969-gtr-89-32-build/#findComment-5839361
Share on other sites

If going with a higher flowing pump then yes you need a bigger capacity sump, head restrictors etc (replacing with a R33 crank for the long oil drive would be recommended). read the oil control thread in it's entirety.. as for head oil drains, as far as their function.. the general consensus is they don't really work.

I wouldn't risk using that balancer again if there were a oil pump failure.

Ok I already have restrictor s etc but not the sump do u recommend me changing sump ? Where is good place to get on if so

What is a good brand/model of harmonic balencer ? To replace standard one with ? And where could I source a 33 crank from ? Would itbe cheaper to go collar and change harmonic bal ?

Link to comment
https://www.sau.com.au/forums/topic/365969-gtr-89-32-build/#findComment-5839438
Share on other sites

Try Justjap for the R33 crank, from memory they arent that expensive.

As for the sump, from my reading I would retain the factory item. There doesnt seem to be much move towards aftermarket sumps in a basic sort of setup.

GL

Link to comment
https://www.sau.com.au/forums/topic/365969-gtr-89-32-build/#findComment-5839635
Share on other sites

it's as simple as this really. factory pump factory sump. aftermarket pump? aftermarket sump. a high flowing pump will empty your stock sump in a matter of seconds. literally. and with much less oil flowing back down it doesn't take long for the sump to run dry.

so if you want to run a jun pump, you need to get an enlarged and baffled sump. I've had no problems with trust sumps on 2 of my GTRs and the hi-octane sumps seem to work very well too. I'd buy one of those.

as far as balancer goes I'd either spend a little and buy an N1 balancer, or go for top of the line which is ATI.

Link to comment
https://www.sau.com.au/forums/topic/365969-gtr-89-32-build/#findComment-5840477
Share on other sites

it's as simple as this really. factory pump factory sump. aftermarket pump? aftermarket sump. a high flowing pump will empty your stock sump in a matter of seconds. literally. and with much less oil flowing back down it doesn't take long for the sump to run dry.

so if you want to run a jun pump, you need to get an enlarged and baffled sump. I've had no problems with trust sumps on 2 of my GTRs and the hi-octane sumps seem to work very well too. I'd buy one of those.

as far as balancer goes I'd either spend a little and buy an N1 balancer, or go for top of the line which is ATI.

I think he's right!

Link to comment
https://www.sau.com.au/forums/topic/365969-gtr-89-32-build/#findComment-5840704
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
    • Why are you so adamant on going M12? Why not follow Brad (GTSBoy) suggestion. You're talking moving from a 1/8" size, to a 1/2" effectively. 4 times bigger. Why skip the commonly available sizes in between? The bigger you go, the more likely you are to strip the threads out at a later date, as guaranteed, someone will put a huge spanner on the M12 and really tighten it up, and you're only in thin wall, so not a lot of threads to engage!
    • Hi. Yeah thanks. Car is already at tuners and it staying there to resolve "many" issues they do not like. So it is in a good hands. Getting a good tune on that Nistune ECU too so the car would be good. Just needs a little tune up and love.
×
×
  • Create New...