Jump to content
SAU Community

Recommended Posts

One of my 32 GTRs sits around a little - say 6 months since last started. Tried to fire it up the other day using jumper leads from GTR II and she wouldn't turn over. Ended up swapping batteries in the end. I grabbed the dead battery and hooked her up to a jigger I've got that maintains the batteries charge, and it won't charge. If I hook the jigger to any other battery I've got either the red light comes on the charger indicating it needs a top up or the green light comes on telling me the battery is 'full'. So the battery from my oft not used GTR seems to be stuffed. I didn't disconnect it whilst it was sitting around, which in hindsight I probably should have done. So my questions are:

Is my battery stuffed or do I need to hook it up to a proper trickle charger to breath some life into it?

What stuffed the battery? It just sat there after all. Why can't I charge it up? It was new a couple of years ago and gets little use.

How should you store your battery in a car with very infrequent use? (this car is not parked where the jigger can be used). Out of car hooked up to the jigger? Just disconnect and charge up the night before you need to use it?

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/366668-dead-battery/
Share on other sites

Is my battery stuffed or do I need to hook it up to a proper trickle charger to breath some life into it?

What stuffed the battery? It just sat there after all. Why can't I charge it up? It was new a couple of years ago and gets little use.

Thanks.

Thats what killed it... not using it. Get yourself a trickle charger plug it in and leave it. I have one on mine. If I dont put it on charge my car will not start after one week of sitting in the garage!

Link to comment
https://www.sau.com.au/forums/topic/366668-dead-battery/#findComment-5849143
Share on other sites

Yeah, I know lack of use killed it, but killed it for good? I'd have thought I could bring it back from the dead but it doesn't look that way as it won't charge on my charger / charge maintenance jigger. Is it a chuck out job?

Link to comment
https://www.sau.com.au/forums/topic/366668-dead-battery/#findComment-5849193
Share on other sites

Thats what killed it... not using it. Get yourself a trickle charger plug it in and leave it. I have one on mine. If I dont put it on charge my car will not start after one week of sitting in the garage!

+ 1. . .batterys that are allowed to go flat frequently will shit themselves and wont recharge, suggest you get a new battery and when its not in use take it out of the car and put it on charge (away from the car) once every couple of weeks, also makes it harder if some f@#ker is trying to steal your car
Link to comment
https://www.sau.com.au/forums/topic/366668-dead-battery/#findComment-5849195
Share on other sites

your charger may not kick in if the charge in the battery has fallen below a certain voltage. but then if your batt voltage is that low and has been sitting for a while its prob not recoverable.

a sitting battery usually wont die if it still has a charge but a flat battery will die quickly if left sitting

Link to comment
https://www.sau.com.au/forums/topic/366668-dead-battery/#findComment-5851712
Share on other sites

your charger may not kick in if the charge in the battery has fallen below a certain voltage. but then if your batt voltage is that low and has been sitting for a while its prob not recoverable.

a sitting battery usually wont die if it still has a charge but a flat battery will die quickly if left sitting

Prolly should have said there is a voltage leak somewhere and the battery normally goes dead after 2 weeks. It sat in the car subject to the leak for 6-8 months. Sounds like I've killed it. So new battery needed and this time I'll keep it out of the car (not on concrete) and on a top up charger.

Link to comment
https://www.sau.com.au/forums/topic/366668-dead-battery/#findComment-5852238
Share on other sites

Change the water in the battery see if that helps... But seriously it cost no more than $60 for a good century battery, just get a new one.

My battery goes shit after a week or two of not driving. Turns over very slowly, not fast enough to fire the engine so needs to be jumped.

Edited by SargeRX8
Link to comment
https://www.sau.com.au/forums/topic/366668-dead-battery/#findComment-5853504
Share on other sites

Change the water in the battery see if that helps... But seriously it cost no more than $60 for a good century battery, just get a new one.

My battery goes shit after a week or two of not driving. Turns over very slowly, not fast enough to fire the engine so needs to be jumped.

You should never "change" the water In a battery. Just buy some distiller water and top it up with that

Link to comment
https://www.sau.com.au/forums/topic/366668-dead-battery/#findComment-5853561
Share on other sites

You should never "change" the water In a battery. Just buy some distiller water and top it up with that

Ah lol should have phrased my self a little better but yeah, just get that distilled water from woolies or kmart or something and top her up.

Cheers for pointing it out!

Link to comment
https://www.sau.com.au/forums/topic/366668-dead-battery/#findComment-5855472
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...