Jump to content
SAU Community

Recommended Posts

guys name is Cam Gigandet, he was the bad guy in the original Twilight, also the bad guy in Never Back Down.

pretty sure he was the "heart throb" in that movie with Christina Agulira.....

no homo

Ahhh Interesting... *google*

He looked retarded as a bad guy in Twilight, but Robert Pattinson also looked much better in Remember me and Harry potter and the goblet of fire than he does in Twilight, except the sparkles, I like sparkles, think its the whole vampire thing, David Boreanaz however still looked hot as Angel...

Burlesque he wore makeup - Probably why I didn't notice...

Haven't seen Never Back Down... If he wears no shirt, this may be an interesting movie... :)

Please, don't quote the picture again. It's depressing to know that the leftovers of my next meal will find their way to the bin, when there's guys like that getting around. Scrawny bastard

Hey, careful what you say, Zane is much much smaller than that! :domokun: Don't make me hurt you lol

Hey, careful what you say, Zane is much much smaller than that! :domokun: Don't make me hurt you lol

Zane doesn't look unhealthy though. Girls going head over heals when they see a thin framed guy with f**k all body fat piss me off. Anyone can look like that, it's simple - stop eating.

A skinny guy with abs is like a fat girl with big boobs - it doesn't count.

Cam was nearly 80kg in Never Back Down mate, hardly think he needs to eat....

Like it or not he is a naturally thin and small framed guy, would be hard for him to get big. The look he was also after was a that of a slim fighter.

Women like it, I workout for the women so if I could achieve and sustain that , I'd be happy...

Cam was nearly 80kg in Never Back Down mate, hardly think he needs to eat....

Like it or not he is a naturally thin and small framed guy, would be hard for him to get big. The look he was also after was a that of a slim fighter.

Women like it, I workout for the women so if I could achieve and sustain that , I'd be happy...

Might just be the photo you put up then, coz in that pic he looks f**king tiny and malnourished haha.

I'm not picking, just saying :P

like this thread wasn't gay enough BEFORE the twilight references

haha oh so true.

I believe he was down near 3% body fat.

which I guess gives that look off. but also he doesnt do any weight training apparently, only stuff like pushups, pull ups yadda yadda.

so the rumors go

She is real... Not like most... She even has real boobs... (Don't ask how I know so much, it is far less suspect than it seems) lol she is like the girl next door... That lives further away... And earns more...

Less Gay??

post-57984-0-24094700-1322470224_thumb.jpg

much better... +1 for real boobs, can't stand obviously fake implant jobs... like the stripper we had give us a lap-dance at my mates bucks a few weeks ago, she was doing the booby shake thing but they didn't move... at all... was weird (don't get me wrong the rest of her was lovely)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...