Jump to content
SAU Community

Crank Collar Clearance Issue

urtwhistle

By urtwhistle,
in Engines & Forced Induction

 Share

Recommended Posts

urtwhistle Proficient

urtwhistle

Posted
Posted

Hey guys,

I have done a bit of a search and can't find any thing that helps.

I have just had my rb30 crank machined and a crank collar put on. I just test fitted the oil pump gear on the collar and noticed there seems to be a lot more clearance than what I would have expected. I measured a total of 12 thou, Ie 6 though on each flat face. Firstly is that normal? that amount of slop I would have expected to negate the whole purpose of the collar.

Do people shim up there gears? I'm think about getting 2 small peices 4 thou shim and loctite 406'ing it to the crank collar just to tighten it up a little. I noticed tonight that the glue added about 1 thou. so In theory it would bring it down to about 2 thou.

What does every 1 else do?

Lastly when using a standard rb25 pump on a built rb30, do people put say a 2mm washer in the oil relief valve?

regards

Chris

Link to comment
https://www.sau.com.au/forums/topic/368570-crank-collar-clearance-issue/
Share on other sites
bubba Grand Master

bubba

Posted
Posted

Chris, that is why I'm a fan of welding the snout up and machining to suit the particular gears you are using. For me, 12thou is way too much slop!

As for the oil pump relief, I'm running a stock RB30E pump on my next engine and I shimmed the relief spring with an approx. 2mm washer.

urtwhistle Proficient

urtwhistle

Posted
  • Author
Posted

Hey Mr Bubs, In hind sight I think your onto something and I probably should have gone the welded route.

12 thou makes the oil pump gear rock back and forth like its on a rocking chair. I don't understand why there isn't alot more post's relating to this subject I mean its so damn obvious to me lol

r33_racer Grand Master

r33_racer

Posted
Posted

Yeh that point is a good one. However, What does the clearance become when the engine is running and everything has heated up and expanded?

Also another point is the crank doesnt run perfectly centred at xxxx rpm, there is always a certain amount of runout. Too tight on that clearance and it will be just as bad as not having a collar at all. How much runout there is i dont know, But there is no way the snout is always perfectly centred when your at 7000rpm bouncing off the limiter.

But 0.012" is alot, and no doubt it can probably be run abit tighter. But there is no way of knowing until someone who has run tighter can say its been fine and tells you what clearance they actually did run. Or you try it yourself and see what happens.

But I dont think 0.002" is enough. Hopefully someone else with more exp can shed some light here.

If I was going to machine a collar Id probably aim for about 0.006" overall, 0.003" per side. But thats just my own guess. Without knowing expansion and run out its hard to say.

MrStabby Grand Master

MrStabby

Posted
Posted

Yeh that point is a good one. However, What does the clearance become when the engine is running and everything has heated up and expanded?

If both pieces are made from the same metal (or if they have the same coefficient of thermal expansion), the clearance will not change if they stay at the same temperature.

t_revz Grand Master

t_revz

Posted
Posted

Chris, that is why I'm a fan of welding the snout up and machining to suit the particular gears you are using. For me, 12thou is way too much slop!

how hard did this hit the back pocket? significantly more than collar?

urtwhistle Proficient

urtwhistle

Posted
  • Author
Posted

Doesnt the aftermarket crank collars and a std r33/r34 crank measure up the same OD?

I think you might be right but I no longer have the neo Rb25 block to mic it up. I went with the 4thou shim and its still possible a bit tight. I'll have more of a look tonight now that the glue has dried and I can take the sharp edges off the shim.

bubba Grand Master

bubba

Posted
Posted

how hard did this hit the back pocket? significantly more than collar?

Not sure on cost as I haven't done mine yet as my forged build is on hold for a while, chuckie should know soon. We had it done to my mates 30 in his GTS4 and that thing cops an absolute beating, 8500rpm limiter launches and burnouts, still going strong.

Realistically, it should add much onto the cost of machining at all. Wouldn't take more than an hour to weld the snout up and if just fitting a collar the snout needs to be machined right down anyway.

On the topic of crank runout.... why would a splined setup ala JZ, not completely destroy itself?

sky30 Mentor

sky30

Posted
Posted

Not sure on cost as I haven't done mine yet as my forged build is on hold for a while, chuckie should know soon. We had it done to my mates 30 in his GTS4 and that thing cops an absolute beating, 8500rpm limiter launches and burnouts, still going strong.

Realistically, it should add much onto the cost of machining at all. Wouldn't take more than an hour to weld the snout up and if just fitting a collar the snout needs to be machined right down anyway.

On the topic of crank runout.... why would a splined setup ala JZ, not completely destroy itself?

is you mates motor rb26 or rb30?

r33_racer Grand Master

r33_racer

Posted
Posted

Not sure on cost as I haven't done mine yet as my forged build is on hold for a while, chuckie should know soon. We had it done to my mates 30 in his GTS4 and that thing cops an absolute beating, 8500rpm limiter launches and burnouts, still going strong.

Realistically, it should add much onto the cost of machining at all. Wouldn't take more than an hour to weld the snout up and if just fitting a collar the snout needs to be machined right down anyway.

On the topic of crank runout.... why would a splined setup ala JZ, not completely destroy itself?

Whats the 2J setup look like exactly? How many splines and do you know what sort of clearance it runs? No doubt its better then our nissan design. Seems toyota also improves on everything nissan didnt :( Splined from the get go sounds alot better.

Im guessing it probably has ample clearance as well, or maybe their cranks are made of better material and dont flex/runout as much?

bubba Grand Master

bubba

Posted
Posted

is you mates motor rb26 or rb30?

25t/30

We had it done to my mates 30

:thumbsup:

Whats the 2J setup look like exactly? How many splines and do you know what sort of clearance it runs? No doubt its better then our nissan design. Seems toyota also improves on everything nissan didnt :( Splined from the get go sounds alot better.

Im guessing it probably has ample clearance as well, or maybe their cranks are made of better material and dont flex/runout as much?

It looks pretty much like an axle end where it goes into the diff.. as for clearance, I have no idea. Shanef was working on a splined setup for RB's but got ripped off by his machinist or something :/

2JZ-GE oil pump..

oilpump.jpg

urtwhistle Proficient

urtwhistle

Posted
  • Author
Posted

Hey so it turns out that 4tho shim is still too tight and I can't get the oil pump gear on. which is a pain when I know that if the gear is in position I can push 2x 6 tho feeler gauges under it.

Also Loctite 406 is not a valid option as it is extremely hard to get it to key on and stop the shim from peeling off. Thats If you are quick enough to actualy get the glue on without gluing the shim to your hand first.

My boss suggested using Loctite 680 high strength retaining compound. So I'll let you know I go with that experiment.

At the rate I'm going this motor is going to take about 2 years to get running. Almost give you a run for your money ay Bubba????

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • dyl33
      VOLK RACING GTC CENTRE CAPS

      By dyl33 · Posted

      Centre caps $250
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Duncan
      Boost cut after swap(RB25DET NEO) R34

      By Duncan · Posted

      Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...