Jump to content
SAU Community

Recommended Posts

Hi i am rebuilding my engine its an rb25 std bore and motor has done 110,000kms and there appears to be little if no wear in the bore

i am purchasing a set of CP Pistons and a set of Manley Connecting Rods with arp rod bolts for the rebuild and a set of cometic gaskets.

I havnt built a nissan rb 6 cyl engine before is there anything i should be aware of rebuilding it with forged internals as i want to do it once only

When replacing pistons is it recomended to have engine block rebored with oversize pistons or use std size forged pistons

any info would be great i dont want the engine for high horsepower but i want a bit of overkill for the mods i have and the couple i want currently have 430hp hi flowed nissan turbo hybrid fmic a gtr style intake manifold s/steel exhaust manifold low mount 3 inch turbo back exhaust with 3 inch cat and piggy back ecu on to main ecu

thanks for reading this post

Sam....

Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/
Share on other sites

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

You need to be more specific - what is your power goal? Do you need a rebore? Measurement will determine that - how much oversize and out of round. Also measure crankshaft for wear. If the mileage is genuine it is possible you will be able to use standard pistons bearings etc. Have a read of the oil control thread re restrictors.

Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5883676
Share on other sites

are you capeable of doing the work yourself? do you have the tools to measure clearances etc? if no then just pay someone to do the machining and assembly of the motor. regardless of the bore condition i would certail go for a rebore to the next size up. start fresh to give the rings a chance to bed correctly.

Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5883680
Share on other sites

You need to be more specific - what is your power goal? Do you need a rebore? Measurement will determine that - how much oversize and out of round. Also measure crankshaft for wear. If the mileage is genuine it is possible you will be able to use standard pistons bearings etc. Have a read of the oil control thread re restrictors.

Hi thanks for your reply power goal 200-250 rwkw.Taking crank head and block to machine shop tomorrow 2 have them checked i will probably go with a rebore. The reason i want forged bottom end i cracked one of the original pistons and dont want the worry any more. The car will be driven normally 95% of the time and unleash it now and then.

I was also looking at oil pumps and it seems there are as many pros and cons with them not to mention huge cost. Might stick with the K.I.S.S protocol and stick with a standard item.

Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5883804
Share on other sites

After your rebuild the main thing to keep your engine alive is a good tune. Have you got some kind of aftermarket ecu? If not z32 ecu with Nistune chip would be the minimum (and adequate for those power levels) followed by PFC or best a Link/Vipec.

Sorry just reread your post and see you have a piggyback - something like an e-manage would be fine.

Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5883864
Share on other sites

why are you even bothering to rebuild if that is the only power you are after? I ran 300rwkw with a Garrett GT3076 for about 3 years, and when we removed the motor, it still tested perfect in a compression and leak down test.

I wouldn't even bother with a rebuild for your power goal unless the motor is already buggered.

ALso, DEFINITELY get the motor rebored if you are installing new pistons and rings. Forged pistons are sentisive to the right bore size.

Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5883952
Share on other sites

It seems even with a standard oil pump,oil restrictors are advised, 20 bucks a restrictor, there are a couple of billet gear pumps in the parts for sale section. Price of these items will be small fraction at end of build.For your goals, quitting while ahead and buying a used RB25det for $1400 looks good. (price of retail after market oil pump).

Edited by WHITE gtt
Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5884158
Share on other sites

After your rebuild the main thing to keep your engine alive is a good tune. Have you got some kind of aftermarket ecu? If not z32 ecu with Nistune chip would be the minimum (and adequate for those power levels) followed by PFC or best a Link/Vipec.

Sorry just reread your post and see you have a piggyback - something like an e-manage would be fine.

Hi bob thanks for the info left head crank and block at machine shop will get the news tomorrow on condition of items

Sam....

Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5884711
Share on other sites

why are you even bothering to rebuild if that is the only power you are after? I ran 300rwkw with a Garrett GT3076 for about 3 years, and when we removed the motor, it still tested perfect in a compression and leak down test.

I wouldn't even bother with a rebuild for your power goal unless the motor is already buggered.

ALso, DEFINITELY get the motor rebored if you are installing new pistons and rings. Forged pistons are sentisive to the right bore size.

Hi thanks for your input yes its a low pwr outlook at the moment but like to leave room for the futurei have extra mods id like to do in the future so thats why i want a reasonable bottom end.

I would also like it to run the car on a lower octane fuel somewhere in the future.

The original motor was going great never used oil went well no problems then i accidently filled the car up with regular unleaded in canberra and the car was lucky to make it home. Number 3 piston nearly parted company with itself split around oil ring recess was blowing smoke like no tomorrow.I dont want to change engine block as i like to keep the car,s main components original. You never really know what you are getting buying second hand.

Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5884743
Share on other sites

ok no worries mate, didn't realise that you blew your old one.

Take my advice and experience - When you have the block out, get it acid bathed, decked, bored, hone, and the top of the bores chamfered. Should cost you about $300. And you'll have a peice of mind. Trust me, don't skimp in these areas. Especially if you are looking for bigger power later on.

Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5884749
Share on other sites

Hi thanks for your input yes its a low pwr outlook at the moment but like to leave room for the futurei have extra mods id like to do in the future so thats why i want a reasonable bottom end.

I would also like it to run the car on a lower octane fuel somewhere in the future.

The original motor was going great never used oil went well no problems then i accidently filled the car up with regular unleaded in canberra and the car was lucky to make it home. Number 3 piston nearly parted company with itself split around oil ring recess was blowing smoke like no tomorrow.I dont want to change engine block as i like to keep the car,s main components original. You never really know what you are getting buying second hand.

And when a rebuild gos right, there is a special satisfaction.Oil control mods are a reliability mod, needed just as much as forged parts.

Edited by WHITE gtt
Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5884770
Share on other sites

ok no worries mate, didn't realise that you blew your old one.

Take my advice and experience - When you have the block out, get it acid bathed, decked, bored, hone, and the top of the bores chamfered. Should cost you about $300. And you'll have a peice of mind. Trust me, don't skimp in these areas. Especially if you are looking for bigger power later on.

Thanks for your advice has been taken on board just the type of info i was looking for.

I like doing my own rebuilds i have done plenty of engines over the years.

What is your view on oil restrictors to the top of the engine do the lifters suffer ????

thanks Sam....

Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5884931
Share on other sites

Three head oil feeds on an RB25, two block feeds to head, one for VVT. If you restrict two block feeds, you still have three feeds to a hydraulic head. People have adequate cylinder head oil with the VVT feed, one blocked, one restricted.

Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5884958
Share on other sites

I put 2 x 1.3mm restrictors in the block feeds, and welded the head shut on the third feed because I used a RB30 motor. (Doesn't have a third feed for vct). I did the internal pin mod, and robbed 1.5mm worth of feed from the head journal on that side.

Didn't have a single issue with oil what so ever.

Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5885262
Share on other sites

I put 2 x 1.3mm restrictors in the block feeds, and welded the head shut on the third feed because I used a RB30 motor. (Doesn't have a third feed for vct). I did the internal pin mod, and robbed 1.5mm worth of feed from the head journal on that side.

Didn't have a single issue with oil what so ever.

Hi is there a thread on here or website that has info on oil restrictors

also would i have to put restrictors on all 3 oil feeds ??

sorry about all the questions just that id like to get it right

first time.

The car wont see any track work maybe occasional day at drags

and normal driving

Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5894699
Share on other sites

http://www.skylinesa...-drag-or-drift/

This is Sydneykids take on oil control. it seems most RB devotees support oil restriction in a rebuild.He advocates blocking an oil feed in the RB25. Mine and the Mafia is restricting the 2 block feeds.

Edited by WHITE gtt
Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5894716
Share on other sites

  • 4 weeks later...

Update engine build.

I have most of the parts to do my engine rebuild i have

1 set of CP forged pistons + rings pins clips 8.5:1 compression

1 set of Manley con rods/ARP 2000 rod bolts

Nitto Oil Pump +Crank coller

Cometec Gasket set

ARP Head studs

ARP main studs

New Timing belt + idler and tensioners

Engine block i have left the vvt restrictor alone blocked the middle restrictor and installed a 1.5mm restrictor in the rear

Block Head and Crankshaft now at machine shop for chemical clean head surace decked bored and honed and crank coller installed

Waiting to find out what size bearings will be needed

I hope i have not missed anything looking for more input to my rebuild and looking for any more info on anything i may have missed

thanks

Sam...

Link to comment
https://www.sau.com.au/forums/topic/369086-rb25-rebuild/#findComment-5941573
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
×
×
  • Create New...