Jump to content
SAU Community

Recommended Posts

I agree. I love the black leather & electric seats, but the switch gears digs into my thigh a bit on longer trips.

There is a Nissan service bulletin that covers a (potential) fix for this - I posted them on m35.info forum - but I've still not bothered to try it.

  • 4 years later...

Bit of an old thread, but does anyone still do the English conversion for the stereo ? Have just imported an 04 ARX, replaced the suspension with mca x-r's and bushes are up next before it goes for a blue slip.. But the stereo is the next priority after that.. I'm in Sydney if that is relevant.

Many thanks in advance

Ps has anyone been able to get the maps working for Australia ? Not overly important, but curious all the same

I've never seen that second pocket! Mine has a weird Panasonic DVD drive in there for the GPS system.. that'll get ripped out eventually :P

I got it from yahoo auctions in Japan. Yours may have had the screen from factory as mine had the dvd rom in that area.

Problems

 

Turbo Failure:

If the oil lines get blocked, yes your turbo will fail. Clean or replace your lines and your good to go. Drilling your banjo's to 3mm will just cause excessive flow  and encourage oil to leak out the turbine oil ring causing smoke.

The main failure is the ceramic turbine breaking off the turbine shaft. Oil flow is not related to this. The cause is directly related to turbine speed. If you want the OEM turbo charger to last, don't put a dump pipe or exhaust on it, Don't increase boost otherwise it will fail eventually.

 

Rear Shocks:

Upper Mounts will rip out of the car when performance shocks are installed or even with OEM. The top hats rust out due to the stupid design

 

Rust:

They like to rust in the lower kick panel, window frames, gearbox mount point.

 

Air Flow Meters:

The OEM Airflow meters blow continuously. Best by a AFM off ScottyM35 as these are the only ones Ive seen last.. better than getting stuck..buy one straight up

 

Interior:

The interior is just ugly, it squeaks and creaks  

 

Engine:

The engine is capable of serious power and great response. Be warned the head studs are cheese and will leak/lift with almost any detonation. The OEM injectors run out of flow easily so be wary of an M35 Series 1 with an exhaust but no other supporting fueling mods, it will most likely already have a broken piston. Every M35 series one I have compression tested have had at least one piston broken(greater than 10% compression variance). Rocker cover Gaskets go hard and leak. Electronic throttle isn't the most reliable. The coil packs don't like Adelaide 48 degree heat.  

 

Transmission:

This will start slipping on mid throttle changes on the OEM setup when boost is increased and destroy itself. Can only be patched with a shift kit

 

Brakes:

The brakes are hugely undersized and will wrap and crack with any spirited driving.

 

Electric Windows:

The drivers window motor will eventually strip the inner cog. OEM window motors are expensive.

 

Rear Sub Frame:

They can crack at the top of the inverted U. You can't tow

 

Electrical:

The Battery Control Modules are almost all been water damaged at some stage due to blocked drain holes. The rams in the front seats are prone to setting off intermittent Air bag faults. Centre pop up screen is useless, even when converted to English   

 

Stereo:

The original Bose system sounds good, changing it requires a bandwidth adaptor(PAC-OEM2). People charge insane amounts for a Double din fascia.

 

 

Summary:

Buy the series 2, 2wd version with the 3.5ltr if you don't plan on modding the series 1 turbo. If you are looking at going down the turbo path, don't modify it unless you are (a) very patient and capable of your own work or (b) are willing to spend big money with a workshop who actually knows these cars. Buy the car will all the options that you want already...ie AXIS, leather, sunroofs, radar cruise etc. Don't by a turbo version without completing a compression test.

 

 

Matt

 

Edited by BoostdR
8 hours ago, BoostdR said:

Problems

 

Turbo Failure:

If the oil lines get blocked, yes your turbo will fail. Clean or replace your lines and your good to go. Drilling your banjo's to 3mm will just cause excessive flow  and encourage oil to leak out the turbine oil ring causing smoke.

The main failure is the ceramic turbine breaking off the turbine shaft. Oil flow is not related to this. The cause is directly related to turbine speed. If you want the OEM turbo charger to last, don't put a dump pipe or exhaust on it, Don't increase boost otherwise it will fail eventually.

 

Rear Shocks:

Upper Mounts will rip out of the car when performance shocks are installed or even with OEM. The top hats rust out due to the stupid design

 

Rust:

They like to rust in the lower kick panel, window frames, gearbox mount point.

 

Air Flow Meters:

The OEM Airflow meters blow continuously. Best by a AFM off ScottyM35 as these are the only ones Ive seen last.. better than getting stuck..buy one straight up

 

Interior:

The interior is just ugly, it squeaks and creaks  

 

Engine:

The engine is capable of serious power and great response. Be warned the head studs are cheese and will leak/lift with almost any detonation. The OEM injectors run out of flow easily so be wary of an M35 Series 1 with an exhaust but no other supporting fueling mods, it will most likely already have a broken piston. Every M35 series one I have compression tested have had at least one piston broken(greater than 10% compression variance). Rocker cover Gaskets go hard and leak. Electronic throttle isn't the most reliable. The coil packs don't like Adelaide 48 degree heat.  

 

Transmission:

This will start slipping on mid throttle changes on the OEM setup when boost is increased and destroy itself. Can only be patched with a shift kit

 

Brakes:

The brakes are hugely undersized and will wrap and crack with any spirited driving.

 

Electric Windows:

The drivers window motor will eventually strip the inner cog. OEM window motors are expensive.

 

Rear Sub Frame:

They can crack at the top of the inverted U. You can't tow

 

Electrical:

The Battery Control Modules are almost all been water damaged at some stage due to blocked drain holes. The rams in the front seats are prone to setting off intermittent Air bag faults. Centre pop up screen is useless, even when converted to English   

 

Stereo:

The original Bose system sounds good, changing it requires a bandwidth adaptor(PAC-OEM2). People charge insane amounts for a Double din fascia.

 

 

Summary:

Buy the series 2, 2wd version with the 3.5ltr if you don't plan on modding the series 1 turbo. If you are looking at going down the turbo path, don't modify it unless you are (a) very patient and capable of your own work or (b) are willing to spend big money with a workshop who actually knows these cars. Buy the car will all the options that you want already...ie AXIS, leather, sunroofs, radar cruise etc. Don't by a turbo version without completing a compression test.

 

 

Matt

 

Reading you post Matt and i don't want a stagea anymore :).

In other news;

No other car ever built in the history of motoring has ever had any kind of reliability issue.

So probably just go & buy one of those.

Maybe a Jeep; they seem quite good.

  • Like 2

Stock is fine, especially for what I have found so far in these cars... Compared to an "Aussie" made equivalent it's a stark difference in what is considered stock.. And largely where it's tempting to have fun and go all out, I am personally trying to keep it "stock"....

Where OEM parts are available, I would largely go for them, but at the same time, if it's cheaper to put something potentially better on, I know what I would rather do...

On 7/4/2016 at 10:32 AM, West said:

Reading you post Matt and i don't want a stagea anymore :).

So get a PM35.

No turbo to worry about

Different AFM (seems much more reliable)

Nicer interior

Common engine

Updated transmission

 

Really, the only downside to the 3.5L is that there is no turbo.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...