Jump to content
SAU Community

Recommended Posts

When i read that is assumed that they made the changes to make sure that the RPM signal was correct so the graph was displayed correctly, not that they adjusted the ramp rate by 5.7% to make up for the change of ramp rate that the engine sees. But after re reading it i'm not sure?

Even if not the 5.7% difference in load could not be enough to shift the graph 500rpm, I think the differential ratio is a setting you enter in though. 500rpm is the difference in doing a short run say eg 1st/2nd gear equivalent ramp rate vs 4th gear.

  • Replies 101
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Sorry for the slightly OT question but somebody asked this earlier in this thread and I couldn't find the answer... is the GTX3076R available in an internall gated option, and could it even possibly be made to fit a stock manifold and 6-bolt nissan dump? I don't know if there's an exhaust housing for that. What about fitting it into an OP6 housing? :S Sorry if this has been asked a thousand times already... I did search a bit!

turbine side is exactly the same as the normal 3076 so yes theres plenty of turbine housing options including internal and a 6 bolt (although its not very good). however i wouldnt bother getting a gtx3076 if your using the standard manifold and internal gate as a this will become a major restriction before you max out a normal gt3076, let alone a gtx3076

My normal gt3076r hits 18psi at about 3200-3300 rpm. Probably won't be upgrading to the gtx. Unless it's a gtx35

What gear is that in? And is that dyno, or real driving experience? Just curious because thats quite a quick spool for 3076 from what I know..

I think if every last rpm of response is a necessity, and money isnt really an issue, then sure... Any of the GTX variants would be awesome. Some of the results the Evo guys are getting over there in the USA are quite impressive; and thats on 95!

But otherwise the comparable 'standard' GT turbos will suit any purpose just as well.

Awesome results though; I personally expected the GTX to be a little more impressive. Especially considering the hype that it received.. But, somehow, I can't justify spending the extra cash on a turbo which isn't really that much more..... better. A larger GTX perhaps. :thumbsup:

And also for comparison I ran my brother (on the track of course) same setup pretty much exept his is GTX. Mine still spools up faster.

Mind you I only have my exhaust manifold ported. So no major exhaust flow modd

4th gear on dyno. Second gear on street I hit 18psi below 3500

So you have an RB30 or RB28? Or are using Nitrous?

2nd gear 18psi below 3500rpm is HKS 2530 territory on an RB25.

Edited by simpletool

So you have an RB30 or RB28? Or are using Nitrous?

2nd gear 18psi below 3500rpm is HKS 2530 territory on an RB25.

I honestly don't know what the go with it is too. All I have is a unopened rb25 with cam gears and ported exhaust manifold. Most people say it's impossible but I'm not sure what the go is. Just found my autosalon dyno sheet. But boost controller was on the wrong setting and wasn't hitting 18psi till 5000rpm which was gay lol

You won't be able to read it. Because it's in speed. And I had different diff ratios to stock.

there is a formula to convert speed to RPM and vice versa... diff ratio can be callibrated on the dyno but i dont know if matty would have done that...

post anyway man :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...