Jump to content
SAU Community

Brake Line Nut - Not Undoing

ODYSSEYGTR

By ODYSSEYGTR,
in General Maintenance

 Share

Recommended Posts

ODYSSEYGTR Enthusiast

ODYSSEYGTR

Posted
Posted

hey guys, having a bit of trouble right now getting the brake line to unbolt from the caliper. its a 10mm nut but just seems to be strip over when i try undo it,

possibly shitty spanners i have but any suggestions? thanks. can provide pics if necessary

Link to comment
https://www.sau.com.au/forums/topic/370120-brake-line-nut-not-undoing/
Share on other sites
ODYSSEYGTR Enthusiast

ODYSSEYGTR

Posted
  • Author
Posted

Is it just spinning or have you rounded the hex head off?

rounded :( its alright, only rounded on one bit of the nut, so i undid it further up the line and then took it off and got around the other side.

worked a treat ahah, not keen about putting it back on, will probably source another.

simpletool Mentor

simpletool

Posted
Posted (edited)

lots of brands make flare nut spanners. I got some KC tools - they are sweet for cheap. Make sure they are derived from 6-point spanners not 12-point.

Edited by simpletool
MrStabby Grand Master

MrStabby

Posted
Posted

For flare nut (and open ender) spanners its worth spending the dollars to get a good brand IMO. I have some KC flare nut spanners and while they're nicely made i sort of wish i'd gone kinchrome or equivalent. For ring spanners or sockets i'd imagine the KC stuff would be great.

www.vektools.com.au - i think i got my KCs from there too.

tridentt150v Grand Master

tridentt150v

Posted
Posted

And you can get away with say two pipe or flare nut spanners [covering 4 sizes] and they will fit just about every size you will come across in the auto world. So not a big expense really. I have Dowidat ones, top shelf stuff, had em for a while.

tridentt150v Grand Master

tridentt150v

Posted
Posted

probably a vice grips or a small plumbers wrench with the serrated teeth?

there is a tool that I've got that is similar to those and locks on to the nut end, strangely enough, I think its Dowidat as well. I'll have a look when I get home, but I reckon several tool makers would have something like it. Its a butchering tool for when all else fails.

The other tool that comes to mind is a stud remover, but you'd have to have the other end of the pipe undone so you could slip it over and down onto it because these tools are not open ended.

MrStabby Grand Master

MrStabby

Posted
Posted

When one of my turbo lines was just stretching the KC flare nut spanner apart and rounding off the edges, i just cut off the pipe off so i could use a socket, and it came out easily. I figured it was already stuffed enough to warrant replacement, so no problems in cutting it off.

djr81 Grand Master

djr81

Posted
Posted (edited)

probably a vice grips or a small plumbers wrench with the serrated teeth?

there is a tool that I've got that is similar to those and locks on to the nut end, strangely enough, I think its Dowidat as well. I'll have a look when I get home, but I reckon several tool makers would have something like it. Its a butchering tool for when all else fails.

The other tool that comes to mind is a stud remover, but you'd have to have the other end of the pipe undone so you could slip it over and down onto it because these tools are not open ended.

I have used hose spanners for brake work. You usually end up rounding the nuts anyway. The are better than open ended spanners buy not by much.

http://www.sidchrome.com.au/product/7473/5-piece-metric-flare-nut-spanner-set

Now I just use vice grips for undoing stuff. Irwin have a huge range of them. Find the right size with a straight end & you will be fine.

eg:

http://www.irwin.com/tools/locking-tools/fast-release-locking-pliers-sets

Edited by djr81

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...