Jump to content
SAU Community

Recommended Posts

  • Replies 99
  • Created
  • Last Reply

Top Posters In This Topic

just a quick update guys.

made/installed:

greddy oil temp

greddy oil pressure

fitted EL guages but found out the the rev gauge was for a gtr so I couldnt put it in :( still looks good.

fuel pump switch

ingnition switch

blocked off bov

made power steer resivoir bracket

dropped one of my new greddy gauges when I was making the plate and put a dent in it but still works :(

post-11029-0-90460900-1314518293_thumb.jpg

post-11029-0-37970700-1314518307_thumb.jpg

post-11029-0-51460300-1314518326_thumb.jpg

post-11029-0-45011900-1314518340_thumb.jpg

post-11029-0-16252500-1314518362_thumb.jpg

post-11029-0-13089600-1314518380_thumb.jpg

  • 3 weeks later...

yeah the power figure was made on a hub dyno with 2deg of timing put in, made 451rwhp 23psi on the same dyno without the timing. Chucked it on the dyno at powercruise and made 440rwhp so thats a power figure loss of 2.5% from hub to roller. Looking at cams injectors and e85 :)

  • 3 weeks later...

hey guys little update. just got my hands on a piar of 19x9 +13 vs-kf's for the front and in the process of finding some 19x10 +18 ish for the rears :) Mind you this is just for the street :P

post-11029-0-67019500-1317955711_thumb.jpg

post-11029-0-55859000-1317955718_thumb.jpg

  • 2 weeks later...

hey guys little update just fitted a gtr cooler that I swapped for my a.r.e as the end tank were straight and the bar would fit unless I chopped the shit out of it. Also fitted my gtr front bar, series 3 lip should turn up next week sometime and then ill fit my oil cooler :)

post-11029-0-33220900-1318738707_thumb.jpg

post-11029-0-86241200-1318738721_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
×
×
  • Create New...