Jump to content
SAU Community

Recommended Posts

Hello,

Sorry for the plain question, but ->

I'm about to replace my fuel pump ..

I was wondering how the fuel pump+cradle is actually mounted to the chasis.

From looking at the manual it seems there are no bolts that attach the pump assembly

to the car (fuel tank) ?

It must be secured somehow .. musn't it?

Link to comment
https://www.sau.com.au/forums/topic/371704-r33gtst-fuelpump-how-is-it-mounted/
Share on other sites

The top of the fuel pump cradle slides down onto a bracket that is mounted just inside the fuel tank. It's quite hard to explain, but if you open up the lid of your fuel tank, you'll see what I mean. To remove, you have to slide the cradle up and off the bracket. It's fairly self explanatory and easy, the job is just a bitch because it requires small arms and contortionist like flexibility. Probably not that bad if you're just replacing stock for stock, but upgrading to a bigger pump has some fun trial and error to go with it.

Hi there,

Many thanks!

Yes, I thought so (I mean that there is a bracket) ..

So the cradle just slides on it, and nothing to secure it (like a bolt or clip?)

I have a Tomei-Pump which is supposed to be a drop in and forget, so that will be (hopefully) painless.

I also need to pull the fuse off the pump and then let the engine idle till the fuel pressure has dropped, right?

?

The top of the fuel pump cradle slides down onto a bracket that is mounted just inside the fuel tank. It's quite hard to explain, but if you open up the lid of your fuel tank, you'll see what I mean. To remove, you have to slide the cradle up and off the bracket. It's fairly self explanatory and easy, the job is just a bitch because it requires small arms and contortionist like flexibility. Probably not that bad if you're just replacing stock for stock, but upgrading to a bigger pump has some fun trial and error to go with it.

Nothing to secure it...it relies on gravity, plus it slides a fair way down on the bracket, so it is fairly secure. In fact, when I put in my Bosch 040, I could only slide the top of the cradle half way down the bracket and it's still secure.

Don't know about the removing of fuses and engine stalling...I did mine without all this...shouldn't be any pressure after you've had the engine off for more than a few minutes.

Nothing to secure it...it relies on gravity, plus it slides a fair way down on the bracket, so it is fairly secure. In fact, when I put in my Bosch 040, I could only slide the top of the cradle half way down the bracket and it's still secure.

Don't know about the removing of fuses and engine stalling...I did mine without all this...shouldn't be any pressure after you've had the engine off for more than a few minutes.

days later I had fuel squirting everywhere lol just cover it up with a old towel when you remove the lines.

days later I had fuel squirting everywhere lol just cover it up with a old towel when you remove the lines.

Oh ok...maybe changes in air temperature pressurised your fuel over time :P

There was seriously very little, if any, fuel that came out when I disconnected the lines...so I don't know what's going on there lol.

just put a nismo in my 33gtst, very easy, probably took 15 minutes of dicking around just trying to get it back on the cradle though. replaced a bosch 040 that i just couldnt get back on, and i easily spent over an hour on it and gave up.

Just put a torch in the tank when you've removed it and you will see how easy it actually is to put on

Hi ...

How do I remove the fuel lines (the 2 with the quick fit connector)

How does the connector work? (sorry, never seen these before)

Also did you use a hammer to remove loosen the big plastic nut?

(I would make a tool for this, but don't have the time at the moment ..)

Thanks!

just put a nismo in my 33gtst, very easy, probably took 15 minutes of dicking around just trying to get it back on the cradle though. replaced a bosch 040 that i just couldnt get back on, and i easily spent over an hour on it and gave up.

Just put a torch in the tank when you've removed it and you will see how easy it actually is to put on

i just used pliers to squeeze clamps together then pulled the hose off. although i had trouble with the feed line and ended up replacing it with new line, only because the feed line had no extra slack in it, i think it was about 63cm long so i just got 70cm worth.

i just used a big flathead screwdriver and a hammer to get it off

The top 2 hoses are return and the bottom one is the feed. Is that what you meant by connector thing?

post-29115-0-53695500-1311558692_thumb.jpg

or the wire connector? its just acts like a connecting point with wires both side

post-29115-0-55276800-1311558929_thumb.jpg

bracket intank

post-29115-0-86725100-1311558978_thumb.jpg

Hi ...

How do I remove the fuel lines (the 2 with the quick fit connector)

How does the connector work? (sorry, never seen these before)

Also did you use a hammer to remove loosen the big plastic nut?

(I would make a tool for this, but don't have the time at the moment ..)

Thanks!

Hi there,

Thanks for the pictures and advice :)

I have attached a pictures of the hoses, I hope that makes it clearer.

(I have a Spec2, so I guess that's why I have these)

i just used pliers to squeeze clamps together then pulled the hose off. although i had trouble with the feed line and ended up replacing it with new line, only because the feed line had no extra slack in it, i think it was about 63cm long so i just got 70cm worth.

i just used a big flathead screwdriver and a hammer to get it off

post-33912-0-83948000-1311575267_thumb.jpg

Edited by Torques
  • 2 weeks later...

Hello there,

Just wanted to report that I recently changed the pump to a Tomei.

It all went alright, and the hardest part was probably fitting the fuel pump back in.

This was due to my big hand and the limited space in the tank.

Also I should have emptied the fuel tank more; I got quite dizzy from the fumes and my skin being

washed in fuel.

:)

Hi there,

Thanks for the pictures and advice :)

I have attached a pictures of the hoses, I hope that makes it clearer.

(I have a Spec2, so I guess that's why I have these)

  • 8 years later...
On 23/07/2011 at 11:09 AM, mattis96 said:

just put a nismo in my 33gtst, very easy, probably took 15 minutes of dicking around just trying to get it back on the cradle though. replaced a bosch 040 that i just couldnt get back on, and i easily spent over an hour on it and gave up.

Just put a torch in the tank when you've removed it and you will see how easy it actually is to put on

Sorry I’m new here.     I am having a shocking time trying to work out the pump cradle mounting.   As it wasn’t mounted when I removed it

Well I hope you have a low fuel level because as a first timer it helps you to see what you need to do.

The cradle is a longish flat looking bracket that slides into and then clip locates in a plastic holder on the front of the tank.

Have a look, stand back and use an LED torch [try to avoid arcs and sparks] and see if you can see and feel the plastic holder.

Once you do you will sort of realise how the bracket slides down and then clips in place.

There is probably a tutorial in the How To section on this forum that will help, and good ole YouTube is always a 'go to'.

Maybe this: 

 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
    • Well the articals keep saying a Q50s (Skyline in Japan) with a new Manual gearbox. I like the talk about the new looks with the round tail lights. I hope they bring back the retro look like they did with the Z
    • Off the back of feedback we have decided to mix up this next Motorkhana at Avalon to have some targeted skills practice for beginners to advanced. Saturday 6th September 2025 8:30am Capped 26 entries Standard Entry Fee: $89 Members Entry Fee: $55 (SAU Victoria Only) Entries Close: Friday 5th February  Where: 55 beach road Avalon. https://maps.app.goo.gl/HNUE3EuNue3sJxh38 Entries: Limited to 26 entrants (Passengers allowed over the age of 14 with a signed disclaimer and same safety gear) Disclaimer: Download  Please electronically sign and email to [email protected] or print and hand in and Driver Sign In. To compete in this event you will require A valid  AASA General Speed licence or (Day license via the AASA Website for $50) MA Licenses are no longer accepted by AASA https://aasa.com.au/  A helmet, long sleeve clothing and a 1KG mounted fire extinguisher recommended (But not Mandatory). Further details within Supp Regs on the enty link. Entry Link > https://www.sauvic.com.au/entry/deca/20250906 You can bring and have a passenger in the car but they need to comply to the same safety and clothing as driver. Bring your car and get to battle others, win, lose or draw. I can guarantee you will have lots of fun. Any questions email [email protected] Entry List: 1.Anna S 2. Luke S 3. Jesse Givens-Lamb 4. Luca Stamatescu 5. Madeleine Stamatescu    
    • Wanna rewrite all of that in, say, 2 or 3 separate sentences, so that we can read it?
×
×
  • Create New...