Jump to content
SAU Community

Recommended Posts

Hello,

Sorry for the plain question, but ->

I'm about to replace my fuel pump ..

I was wondering how the fuel pump+cradle is actually mounted to the chasis.

From looking at the manual it seems there are no bolts that attach the pump assembly

to the car (fuel tank) ?

It must be secured somehow .. musn't it?

Link to comment
https://www.sau.com.au/forums/topic/371704-r33gtst-fuelpump-how-is-it-mounted/
Share on other sites

The top of the fuel pump cradle slides down onto a bracket that is mounted just inside the fuel tank. It's quite hard to explain, but if you open up the lid of your fuel tank, you'll see what I mean. To remove, you have to slide the cradle up and off the bracket. It's fairly self explanatory and easy, the job is just a bitch because it requires small arms and contortionist like flexibility. Probably not that bad if you're just replacing stock for stock, but upgrading to a bigger pump has some fun trial and error to go with it.

Hi there,

Many thanks!

Yes, I thought so (I mean that there is a bracket) ..

So the cradle just slides on it, and nothing to secure it (like a bolt or clip?)

I have a Tomei-Pump which is supposed to be a drop in and forget, so that will be (hopefully) painless.

I also need to pull the fuse off the pump and then let the engine idle till the fuel pressure has dropped, right?

?

The top of the fuel pump cradle slides down onto a bracket that is mounted just inside the fuel tank. It's quite hard to explain, but if you open up the lid of your fuel tank, you'll see what I mean. To remove, you have to slide the cradle up and off the bracket. It's fairly self explanatory and easy, the job is just a bitch because it requires small arms and contortionist like flexibility. Probably not that bad if you're just replacing stock for stock, but upgrading to a bigger pump has some fun trial and error to go with it.

Nothing to secure it...it relies on gravity, plus it slides a fair way down on the bracket, so it is fairly secure. In fact, when I put in my Bosch 040, I could only slide the top of the cradle half way down the bracket and it's still secure.

Don't know about the removing of fuses and engine stalling...I did mine without all this...shouldn't be any pressure after you've had the engine off for more than a few minutes.

Nothing to secure it...it relies on gravity, plus it slides a fair way down on the bracket, so it is fairly secure. In fact, when I put in my Bosch 040, I could only slide the top of the cradle half way down the bracket and it's still secure.

Don't know about the removing of fuses and engine stalling...I did mine without all this...shouldn't be any pressure after you've had the engine off for more than a few minutes.

days later I had fuel squirting everywhere lol just cover it up with a old towel when you remove the lines.

days later I had fuel squirting everywhere lol just cover it up with a old towel when you remove the lines.

Oh ok...maybe changes in air temperature pressurised your fuel over time :P

There was seriously very little, if any, fuel that came out when I disconnected the lines...so I don't know what's going on there lol.

just put a nismo in my 33gtst, very easy, probably took 15 minutes of dicking around just trying to get it back on the cradle though. replaced a bosch 040 that i just couldnt get back on, and i easily spent over an hour on it and gave up.

Just put a torch in the tank when you've removed it and you will see how easy it actually is to put on

Hi ...

How do I remove the fuel lines (the 2 with the quick fit connector)

How does the connector work? (sorry, never seen these before)

Also did you use a hammer to remove loosen the big plastic nut?

(I would make a tool for this, but don't have the time at the moment ..)

Thanks!

just put a nismo in my 33gtst, very easy, probably took 15 minutes of dicking around just trying to get it back on the cradle though. replaced a bosch 040 that i just couldnt get back on, and i easily spent over an hour on it and gave up.

Just put a torch in the tank when you've removed it and you will see how easy it actually is to put on

i just used pliers to squeeze clamps together then pulled the hose off. although i had trouble with the feed line and ended up replacing it with new line, only because the feed line had no extra slack in it, i think it was about 63cm long so i just got 70cm worth.

i just used a big flathead screwdriver and a hammer to get it off

The top 2 hoses are return and the bottom one is the feed. Is that what you meant by connector thing?

post-29115-0-53695500-1311558692_thumb.jpg

or the wire connector? its just acts like a connecting point with wires both side

post-29115-0-55276800-1311558929_thumb.jpg

bracket intank

post-29115-0-86725100-1311558978_thumb.jpg

Hi ...

How do I remove the fuel lines (the 2 with the quick fit connector)

How does the connector work? (sorry, never seen these before)

Also did you use a hammer to remove loosen the big plastic nut?

(I would make a tool for this, but don't have the time at the moment ..)

Thanks!

Hi there,

Thanks for the pictures and advice :)

I have attached a pictures of the hoses, I hope that makes it clearer.

(I have a Spec2, so I guess that's why I have these)

i just used pliers to squeeze clamps together then pulled the hose off. although i had trouble with the feed line and ended up replacing it with new line, only because the feed line had no extra slack in it, i think it was about 63cm long so i just got 70cm worth.

i just used a big flathead screwdriver and a hammer to get it off

post-33912-0-83948000-1311575267_thumb.jpg

Edited by Torques
  • 2 weeks later...

Hello there,

Just wanted to report that I recently changed the pump to a Tomei.

It all went alright, and the hardest part was probably fitting the fuel pump back in.

This was due to my big hand and the limited space in the tank.

Also I should have emptied the fuel tank more; I got quite dizzy from the fumes and my skin being

washed in fuel.

:)

Hi there,

Thanks for the pictures and advice :)

I have attached a pictures of the hoses, I hope that makes it clearer.

(I have a Spec2, so I guess that's why I have these)

  • 8 years later...
On 23/07/2011 at 11:09 AM, mattis96 said:

just put a nismo in my 33gtst, very easy, probably took 15 minutes of dicking around just trying to get it back on the cradle though. replaced a bosch 040 that i just couldnt get back on, and i easily spent over an hour on it and gave up.

Just put a torch in the tank when you've removed it and you will see how easy it actually is to put on

Sorry I’m new here.     I am having a shocking time trying to work out the pump cradle mounting.   As it wasn’t mounted when I removed it

Well I hope you have a low fuel level because as a first timer it helps you to see what you need to do.

The cradle is a longish flat looking bracket that slides into and then clip locates in a plastic holder on the front of the tank.

Have a look, stand back and use an LED torch [try to avoid arcs and sparks] and see if you can see and feel the plastic holder.

Once you do you will sort of realise how the bracket slides down and then clips in place.

There is probably a tutorial in the How To section on this forum that will help, and good ole YouTube is always a 'go to'.

Maybe this: 

 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...