Jump to content
SAU Community

Recommended Posts

Hey all, Ive got a 32gtst with a standard rb20 in it, and what i thought was the standard box, but have been told this is not an RB20 box.

Just trying to work out what it is, and if it's ok to continue using it in my car/or what I should sell it as.

Notice the gearbox is mounted using only 2 holes, and also the shifter sits slightly forward:

Any help would be great,

Cheers - Sam

post-77777-0-05935100-1311749191_thumb.jpg

post-77777-0-02527500-1311749225_thumb.jpg

post-77777-0-11798200-1311749256_thumb.jpg

post-77777-0-57702800-1311749268_thumb.jpg

Edited by Sammy B
Link to comment
https://www.sau.com.au/forums/topic/372236-can-someone-identify-this-gearbox/
Share on other sites

That looks like a CA/SR box, is the yoke sticking out, at the rear of the box? that crossmember is bolted in backwards aswell by the looks of it

CA/SR has the starter motor bolts facing the other way and no the crossmember is around the right way. The high side is the exhaust/passenger side

That gearstick position is what happens when you put RB20 manual into RB20 auto body. The holes are in different locations. Not a problem, except it causes the rubber boot to push the gear stick backwards a little when in odd numbered gears.

My 32 was auto before its conversion and i don't have this problem

Have you had your vehichle fasted? You can see if it came from factory with an auto.

No, I have not had it fasted. That may help work out if it was perviously auto, but I still have no solid idea what that gearbox is from. Also if it is a ca/sr box is there any reason why I shouldnt continue using it?

Any thing i should check/pictures i could take to help determine what it is?

Well, so was mine, and I do (although it's not a problem). Must be different by year or something.

could be a r31/vl gearbox . as for the hole position , i vaguely remember a friend of a friend of a friend of a mate telling me that they spaced the front crossmember/engine mount points (or something like that) slightly different in the auto (something about the bellhousing on the auto bla bla) .

Disclaimer: don't take this information as gospel , i didn't personally discover this nor have any intrest at the time of what the guy was talking about so information is fairly sketchy

could be a r31/vl gearbox . as for the hole position , i vaguely remember a friend of a friend of a friend of a mate telling me that they spaced the front crossmember/engine mount points (or something like that) slightly different in the auto (something about the bellhousing on the auto bla bla) .

Disclaimer: don't take this information as gospel , i didn't personally discover this nor have any intrest at the time of what the guy was talking about so information is fairly sketchy

I've had both an RB20DET box and the current RB25DE box in there and the stick position is dead the same. Apart from ratios, those two boxes are identical anyway. Can't comment on stick position of RB30E box, as I have had one within 20' of my car.

You have the wrong mount on the back as well. There is about 5 different brackets for nissan. they are a,b,c,d,e

I think you need the ( a ) bracket for that conversion and it will line up with the bolt holes for the original mount

i still reakon, it is a short type fs5w71 bolted to an RB20 bell housing.

same crap as they are talkign about below (but obviously dif. combination of boxes, most of the bell housings are the same length, but the main shafts vary in length after the sandwich plate, and the rear of the box can be longer & shorter depending on what it is or in, sometimes you have to change the input shaft or the front bearing plate that bolts to tht bell housing. you get what i am saying

http://club-s12.org/v3/index.php?topic=12333.0

Just checked the plate on the firewall, appears it did used to be auto (reads RE4R01a)

If its working fine just leave it there

Working fine, but the clutch is on it's way out, so the box has gotta come out either way (just a matter of whether it goes back in or not)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...